ION Optix MyoCam-S Hardware Manual Download Page 16

Page: 16 / 17

Technical Specifications:

MyoCam-S Hardware Manual

Technical Specifications

Here are the specifications for the various parts of the MyoCam-S

Power Supply

Input Power

100-240VAC, 50-60Hz, 1.5A fuse

Power Entry

NEMA standard for removable power cord

Auxiliary In/Out

Phase-locked programmable output clock, Frame start and programmable
frame delay output pulses, Trigger input

Synchronization

Frame-level synchronization between master/slave cameras using Sync In/
Sync Out

Camera connector

Female DVI-I dual-link connector

Camera

CCD Sensor

774 pixels wide by 245 lines (progressive) or 490 lines (interlaced)

USB connector

USB "B" connector

Power supply conn.

Female DVI-I dual-link connector

Acquisition Options

Sampling modes

Progressive or Interlaced

Sample resolution

12-bit A/D converter with 8-bit or 12-bit readout

Integration time

Programmable, 10us - 0.6s

Pixel clock

High-speed (24Mhz), medium (12Mhz) and low-noise (1MHz)

Frame Rates (8-bit)

97Hz (245 lines), 250Hz (87 lines), 500Hz (36 lines), 1000Hz (10 lines)

Gain/offset

Programmable, analog

Software Compatibility

General

Windows DirectShow compatible drivers

Supported versions

Windows XP, Windows 32-Bit Vista only

Cables (supplied)

Camera to Power sup Six foot DVI-D dual-link cable
USB

Six foot USB 2.0 cable

Power Cord

Six foot NEMA to U.S. or European plug

Summary of Contents for MyoCam-S


















Search results

Summary of Contents for MyoCam-S

Reviews:

Related manuals for MyoCam-S

Brands by name

Popular brands

ION Optix MyoCam-S, Hardware Manual

Search results

Summary of Contents for MyoCam-S

Reviews:

Related manuals for MyoCam-S

Brands by name

Popular brands