background image

 

 

-

 19 

-

 

 

 

 

f.

 

Do the chassis support mirrored OS disks? 

In Win IW-RSXXX-02M models supports at least 2 internal disks, RS424-02M and RS424-02M have built-

in 2bay hot swap module. Yet, the disk mirroring is defined by your motherboard or your RAID 1 

controller card. You may check the vendor’s guide to mirror your OS disks. 

 

g.

 

Can it support small form factor MB such as M-ATX and Mini-ITX? 

In Win IW-RSXXX-02M supports motherboard range from Mini-ITX to EEB. Unless you would like to 

mount a customized motherboard which not meet Intel’s standard, you will need to contact In Win 

partners or sales for customization service. 

 

h.

 

Do I need a RAID controller card to connect the backplane? 

If you would like to construct a solid hardware RAID system, it is required. However, using the RAID 

controller card or not, is depends on your purpose and budget. We recommend discussing with In 

Win’s channel partner for their suggestions. 

 

i.

 

Where can I buy the SAS cable? 

6Gb SAS to 4 SATA or 6Gb SAS to 6Gb SAS are standard cable that you easily buy from many vendors. 

You can buy the verified cable from In Win to eliminate the compatibility issues. 

 

Summary of Contents for IW-RS104-02M





















Reviews: