background image

14 

Invisible Fence

®

 Brand R21 v4.0 Titanium Computer Collar

®

 

Power Cap

®

 Battery Status: 

The ICT 801, ICT 802, and ICT 810 Transmitters utilize the R21 v4.0 Titanium 
Computer Collar

®

 receiver. This receiver monitors Power Cap

®

 battery status and will 

alert the owner when the Power Cap

®

 battery needs to be replaced. A Power Cap

®

 

battery test is also performed each time it is inserted into the Computer Collar

®

 receiver. 

 

 
 
 

 
 
 
 

When the Power Cap

®

 battery is inserted: 

The LED status indicator shows GREEN for up to 1 second while testing, and then 
blinks (4 times) one of the following 3 colors to indicate the Power Cap

®

 battery status:  

• GREEN = Power Cap

®

 battery is good.  

• YELLOW = Replace the Power Cap

®

 battery. 

 RED = Replace NOW! Do not rely on the Invisible Fence

®

 Brand system to 

contain the pet. The owner must become familiar with the Power Cap

®

 

battery status indicators. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

For detailed instructions on how to program the R21 v4.0 Titanium Computer Collar

® 

receiver, please refer to the CF-2200 Programming Tool Manual. 

 

 

LED Status Indicator 
(Top view of R21 v4.0 Titanium Computer Collar

®

 receiver) 

•  DO NOT RELY ON THE INVISIBLE 

FENCE

®

 BRAND SYSTEM TO KEEP 

THE PET CONTAINED!  

•  Replace the Power Cap

®

 

•  When a replacement Power Cap

®

 is 

installed and signal field checked, the 
Invisible Fence

®

 Brand System is 

ready for pet containment. 

Power Cap

®

 is dead 

Flashing Red 

•  Replace Power Cap

®

 - The Power 

Cap

®

has lost most of its power.

Power Cap

®

 is low 

Flashing Yellow 

•  No Action Required

 

Power Cap

®

 

is good

 

No light 

Action Required 

Condition 

LED Indicator 

R21 v4.0 Titanium Computer Collar

®

 Status Light Indicator 

Summary of Contents for ICT 801

















Reviews: