background image

70

 

 

When there is a need of installing telemetry module in vicinity of medical equipment  

one has to contact the manufacturer of this equipment in order to make sure that the 
equipment is adequately protected against interference of radio frequency waves (RF). 

 

9.2.4. RF Marked equipment 
 

The restriction against installing telemetry modules in areas marked as radio frequency 
(RF) prohibition zones must be unconditionally observed. 

 
 

9.3. Explosive environment 
 

Installation of telemetry modules in the environment where explosion hazard is present 
is not permitted. Usually, but not always, these places are marked with warning signs. 

Where there is no marking do not install telemetry modules at liquid or gas fuels stores, 
inflammable materials stores, nor places contaminated with metal or wheat dust. 

 

 

10. Appendices 
 

10.1. Register of changes 
 

Current version -

 

v1.51.02 

---------------------------------------------------------------- 

 

v1.51.02

 - 2012-08-01 

 



added new prefix #Fx (x-number of digits after dot) to the SMS commands allowing to 
present values from 16-bit registers as numbers with decimal fraction

 



SMS and E-mail sending rules are merged into one block of Messages sending rules. 
This allow to choose channel of communication from: "SMS", "e-mail", "e-mail or 
SMS" where last option sends SMS where unable to send e-mail for some reason (e.g. 
no GPRS available)

 



added three new predefined symbolic names for use in SMS and e-mail commands: 
#NAME (gives name of device defined during configuration)), #SERIAL (gives serial 
number of device) i #IPADDR (gives current IP address of module).

 



added GPRS testing address and Idle time parameters used for GPRS connection 
check

 



added possibility to write to multiple registers at once using Monitoring - software 
module of MTM

 

 

v1.50.01

 - 2012-04-16 

 



added email sending functionality (via SMTP server and GPRS service)

 

 
v1.00.12 

- 2011-03-31 

 

• improvement in access to read/write resources from memory map via USB port 

 
v1.00.11 

- 2011-03-03 

 

• improvement in answer for blank SMS 
• improvement in procedure of sending SMS with '$' sign (without answer) 

• improvement in roaming procedure 
• added access to read/write resources from memory map via USB port 

------------------------- 

v1.00

 

- First official version   

Summary of Contents for MT-021































































































Reviews: