background image

39

 

 

whether transmission is still possible. The frame is sent to the 

address specified by parameter 

GPRS testing IP address

, if 

different than 0.0.0.0. 

Lack of reply to sent ping frame after exercising defined 
timeout and number of retries is considered as GPRS 

connection loss and resets modem. 

 

 
6.2.5. Authorized numbers 
 

Group 

Authorized numbers

 comprises lists of phone numbers the module is going to 

communicate with. 

 

 

6.2.5.1. Number of phone numbers 

 

Function 

-  Defines the length of phone numbers list authorized to 

exchange SMS messages. 

Data type 

- Number 

Range 

1…32 

Default value 

Comments 

-  The value of this parameter may vary as the result of 

adding/deleting when using the context menu operating 

directly on 

Phone 

  number. The module will communicate 

only with units with the phone number present on the list. 
Read more in 

Syntax for reading and writing data in SMS 

mode

 chapter of Appendices.   

 

 

6.2.5.2. Update phone numbers from SIM card 

 

Function 

-  Enables synchronization of 

Authorized numbers\Phone

 list 

with phone book saved on Defines the length of phone 
numbers list authorized to exchange SMS messages. 

Data type 

- selection 

list 

Range 

Yes 

synchronization is on 

No 

synchronization is off 

Default value 

No 

Comments 

-  Synchronization is done after every reboot of the module, 

after inserting the SIM card or when configuration is written to 
the module. 

The module browses SIM card phone book and if it finds 
entries of the same name as defined in the 

Authorized 

numbers\Phone

 it overrides the numbers from configuration 

with the numbers from the SIM card. 

Those numbers are remembered till module restart. 

 
 

6.2.5.3. Phone number from SIM card always authorized 

 

Function 

-  Enables receiving voice calls authorization for all phone 

numbers stored in SIM card phone book. 

Summary of Contents for MT-021































































































Reviews: