background image

32

This Procedure Includes the Following:

Removing/Installing Batteries without
    Removing Cables

Connecting/Disconnecting Battery Cables

Connecting/Disconnecting Circuit Breaker
    Cables

Replacing  Batteries

When to Charge Batteries

Charging Batteries

Battery Charger Operation

WARNING

For the following procedures, make sure the
ON/OFF switch on the joystick is in the OFF
position.

The use of rubber gloves and safety glasses is
recommended when working with batteries.

Invacare strongly recommends that battery
installation and battery replacement always
be done by a qualified technician.

After ANY adjustments, repair or service and BE-
FORE use, make sure that all attaching hard-
ware is tightened securely - otherwise injury or
damage may result.

CAUTION

The POSITIVE (+) RED battery cable MUST con-
nect to the battery clamp of the POSITIVE
(+) battery terminal/post, otherwise serious
damage will occur to the electrical  system.

REMOVING/INSTALLING
BATTERIES WITHOUT
REMOVING CABLES (FIGURE 1)

NOTE: To install the batteries without removing
cables, reverse the following steps.

Removing

WARNING

Always use a battery lifting strap when lift-
ing a battery. It is the most convenient
method and assures that the battery acid
will not spill. It also helps to prolong the life
of the battery.

DO NOT tip the batteries. Keep the batter-
ies in an upright position.

NOTE: If there is battery acid on the bottom or
the sides of the battery(ies) or on the frame of the
wheelchair, apply baking soda to these areas to
neutralize the battery acid. Before reinstalling the
NEW or EXISTING batteries, clean the baking
soda from the battery(ies).

1. Disconnect the joystick. Refer to DISCON-

NECTING/CONNECTING THE MKIV JOY-
STICK in PROCEDURE 9 of the manual.

2. Remove the seat assembly. Refer to REMOV-

ING/INSTALLING THE SEAT ASSEMBLY in
PROCEDURE 4 of the manual.

3. Remove the shroud. Refer to REMOVING/

INSTALLING THE SHROUD in PROCE-
DURE 7 of the manual.

4. Separate the FRONT frame assembly from

the REAR frame assembly. Refer to TRANS-
PORTING THE WHEELCHAIR in PROCE-
DURE 10 of the manual.

5. Disconnect the battery fastening strap and pull

it through the retaining ring.

CAUTION

Before removing the batteries, it is neces-
sary to disconnect the FRONT battery from
the REAR battery. Otherwise, damage to
the batteries may occur.

B
A

T
T
E

R

I

E
S

BATTERIES

PROCEDURE 9

FIGURE 1 - REMOVING/INSTALLING THE

BATTERIES WITH CABLES

Battery

Fastening

Strap

Retaining

Ring

Front Battery

Rear Battery

Rear Frame Assembly

Disconnect FRONT Battery

from REAR Battery

+

-

+

-

Summary of Contents for Pronto M6

















































Reviews: