Invacare Platinum IRC5LXO2AW Service Manual Download Page 59

Page: 59 / 84

SECTION 19—HOUR METER

SECTION 19—HOUR METER

NOTE: Refer to Recycling Information following local governing ordinances and recycling plans
regarding disposal of the concentrator or components.

Replacing Hour Meter

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical

outlet before servicing.

1. Turn power Off (O) and unplug the unit.

2. Remove cabinet. Refer to Removing Cabinet on page 25.

3. Remove control panel. Refer to Removing Control Panel on page 50.

4. Remove and label the two hour meter connectors and wires connected to back of hour

meter.

5. Squeeze retaining clips on hour meter housing that secure hour meter to control panel.

6. Remove hour meter by pushing meter through front of control panel.

7. Install new hour meter reversing STEPS 4-6.

8. Reinstall control panel. Refer to Removing Control Panel on page 50 and reverse all

steps.

9. Reinstall cabinet. Refer to Removing Cabinet on page 25.

FIGURE 19.1

Replacing Hour Meter

Hour Meter Connectors

Hour Meter

Wires

Hour Meter

Housing

Retaining Clips (Hour

Meter Housing)

Summary of Contents for Platinum IRC5LXO2AW





















































































Search results

Summary of Contents for Platinum IRC5LXO2AW

Reviews:

Related manuals for Platinum IRC5LXO2AW

Brands by name

Popular brands

Invacare Platinum IRC5LXO2AW, Service Manual

Search results

Summary of Contents for Platinum IRC5LXO2AW

Reviews:

Related manuals for Platinum IRC5LXO2AW

Brands by name

Popular brands