Invacare FDX User Manual Download Page 114

Invacare® FDX®

1

IPX4 classification means that the electrical system is protected against spray water.

2

Static stability according to ISO 7176-1 = 9° (15.8 %)

Dynamic stability according to ISO 7176-2 = 6° (10.5 %)

3

Note: The drive range of a mobility device is strongly influenced by external factors, such as the speed setting of the
wheelchair, the charging state of the batteries, surrounding temperature, local topography, road surface characteristics,
tire pressure, weight of user, drive style and use of batteries for lighting, servos etc.

The specified values are theoretical maximum achievable values measured according to ISO 7176-4.

4

Measured without seat cushion

5

Width adjustable for side panel adjustment

6

Telescopic seat frame with sling seat + 30 mm

7

The actual curb weight depends on the fittings your mobility device has been supplied with. Every Invacare mobility
device is weighed when leaving the works. Refer to the nameplate for the curb weight (including batteries) measured.

114

1541361-N

Summary of Contents for FDX

























































































































Reviews: