background image

193

PO

SAVE THESE INSTRUCTIONS

(193PO)  MODEL SF90110T SAND FILTER PUMP  ENGLISH  7.5” X 10.3”  PANTONE 295U  06/21/2013

English

Page 15

Initial startup and operation:

Before operating, be sure that:

  •  All the hoses have been connected and tightened securely, and correct amount of filter sand 

    have been loaded.

  •  The entire system is connected to a grounding type receptacle protected by a ground-fault 

    circuit interrupter (GFCI) or residual current device (RCD). 

OPERATING INSTRUCTIONS (continued

)

CAUTION

The filter control valve has a closed position. The pump should never be on when the 

valve is in the closed position. If the pump is operated with the valve closed, explosive 

situation could exist.  

1.

  Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves 

    to allow water to flow into the sand filter pump.

   NOTE:

 The plunger valve is equipped with a vacuum release valve that will automatically 

    activate to minimize the suction at the pool outlet if the outlet is blocked. This is an additional 

    safety feature to prevent suction entrapment. The vacuum release valve will reset once the 

    blockage is removed and the pump is switched off. To restart the system the air must be 

    removed from the filter pump per previous step.  

2. 

Ensure the drain/waste outlet on the 6-way valve is not covered and directed to a proper 

    draining receptacle.

3.

  Ensure the pump is off, depress the 6-way valve and turn it 

    to the “

BACKWASH

” position 

(see drawings 24 & 29)

.

  

IMPORTANT: To prevent damage to the 6-way valve, 

    always depress the valve handle before turning. Always 

    switch off pump before changing the 6-way valve 

   position. 

4.

  Switch on the pump 

(see drawing 30)

. Water is circulating 

    backward through the sand media and to waste/drain outlet. 

   Backwash until a clear flow of water is observed in the waste/

    drain outlet or through the transparent outlet adaptor.

  

NOTE:

 The initial backwash of the filter is recommended to 

    remove any impurities or fine sand particles in the sand 

   media.

26

27

28

29

1

2

30

OFF

ON

TIMER

Summary of Contents for krystal clear SF90220RC
























Reviews: