background image

6051344      

Rev. 1.0

Page 9 of 17

Step 3: Adding or Changing User Codes.

User codes may be 1 to 6 digits in length

.

  

The 212iLM Mullion has to be in programming mode to add or

change users

Enter Programming Mode: 99

#

 (Master code) 

*

Next enter the user location. (2, 3, 4, etc.) followed by the # key.
Now enter the new code followed by the 

*

 key (Yellow LED flashes rapidly).

Repeat the new code followed by the 

*

 key (Yellow LED flashes slowly).

If the change was successful, the yellow LED will still be flashing slowly.  Codes entered in this fashion
hold the relay time programmed with the master code.

Examples: 

2 # 6789 

*

 6789 

*

3 # 53780 

*

 53780 

*

4 # 23966 

*

 239646 

*

Continue programming or press the 

*

 key again to exit.

Step 4: Creating a User Code With a Different Time, or to Latch/Toggle the Main Relay.

The 212iLM Mullion has to be in programming mode to add or change users

latching or toggle

 code is used to open the relay for an indefinite amount of time.  This operates much

like a light switch.  When you enter a latching user code, the Main relay will activate and stay opened until
the same code or another latching user code is entered to close the relay.

Enter Programming Mode: 99

#

 (Master code) 

*

Next enter the relay time of "00" followed by the # key.
Next enter the user location. (2, 3, 4, etc.) followed by the # key.
Now enter the new code followed by the 

*

 key 

(Yellow LED flashes rapidly).

Repeat the new code followed by the 

*

 key 

(Yellow LED will flash slowly).

If the change was successful, the yellow LED will still be flashing slowly.

Examples: 

00 # 12 # 7788 

*

 7788 

*

00 # 55 # 6632 

*

 6632 

*

00 # 93 # 78651 

*

 78651 

*

Continue programming or press the 

*

 key again to exit.

A

 different output on the main relay

 may be desired for one or more users.  For example, an individual

may require several extra seconds to open a door than everyone else.  If the main relay is set for 5
seconds, that person may need 10 seconds.  A different output time for individual users is programmed
this way.

Enter Programming Mode: 99

#

 (Master code) 

*

Next enter the relay time of "10" followed by the # key.
Next enter the user location. (2, 3, 4, etc.) followed by the # key.
Now enter the new code followed by the 

*

 key (Yellow LED flashes rapidly).

Repeat the new code followed by the 

*

 key (Yellow LED will flash slowly).

If the change was successful, the yellow LED will still be flashing slowly.

Example: 

10 # 12 # 7788 

*

 7788 

*

10 # 55 # 6632 

*

 6632 

*

20 # 93 # 78651 

*

 78651 

*

Continue programming or press the 

*

 key again to exit.

Summary of Contents for 212iLM Mullion


















Reviews: