Intermec RC4030E Reference Manual Download Page 92

Page: 92 / 210

SECTION 5

Norand Open Wireless LAN MIB RC4030E Gateway

5-20 Norand

Management Information Bases Reference Manual

wstIframesRetransmitted OBJECT-TYPE

SYNTAX Counter

ACCESS read-only

STATUS mandatory

DESCRIPTION

“Total number of WTP data frames which were lost and

retransmitted.”

::= { wst 11 }

wstCheckSumErrors OBJECT-TYPE

SYNTAX Counter

ACCESS read-only

STATUS mandatory

DESCRIPTION

“The number of WTP information frames which were discarded

to WTP check sum errors.”

::= { wst 12 }

wstHlDiscardCount OBJECT-TYPE

SYNTAX Counter

ACCESS read-only

STATUS mandatory

DESCRIPTION

“The number of received WTP information frames which were

discarded without being read by a higher layer application.

Received information frames are queued per connection and

should normally not be discarded.”

::= { wst 13 }

wstState OBJECT-TYPE

SYNTAX INTEGER (0..2147483647)

ACCESS read-only

STATUS mandatory

DESCRIPTION

“The internal software state of the WTP module.”

::= { wst 14 }

wstBrgBusy OBJECT-TYPE

SYNTAX INTEGER (0..1)

ACCESS read-only

STATUS mandatory

DESCRIPTION

“The value of wstBrgBusy is 1 if the WTP currently has an

outstanding network transmit request. The value is

otherwise 0.”

::= { wst 15 }

wstT1Timeouts OBJECT-TYPE

SYNTAX Counter

ACCESS read-only

STATUS mandatory

DESCRIPTION

“The total number of times the WTP T1 timer has expired

(i.e. due to lost frames).”

::= { wst 16 }

wstT1Bucket1 OBJECT-TYPE

SYNTAX Counter

ACCESS read-only

STATUS mandatory

DESCRIPTION

“The total number of times that 2 consecutive T1 errors have

occurred.”

::= { wst 17 }

Summary of Contents for RC4030E















































































































































































































Search results

Summary of Contents for RC4030E

Reviews:

Intermec RC4030E, Reference Manual, Page: 92 / 210

Search results

Summary of Contents for RC4030E

Reviews: