background image

34

Appendices

                 

The scanner is on, but the motor is not
rotating. A bar code cannot be read. 
The LED is intermittently flashing red.

The LED is alternating red/green.

The LED is alternating red/green and 
beeps are heard.

The scanner does not accept more than
two or three bar codes.

The LED is red and green.

The LED is blinking red and green.

Diagnostic Tips

 

The scanner is in sleep mode. Press the 

    switch on top of the scanner to reactivate
    the scanner (or use the wake protocol. 
    Refer to section 1.5).

 

Mirror motor is defective and must be

    replaced (Authorized personnel only).

 

Possible failure of the scanning safeguard

    circuit. Immediately disconnect the scanner 

   

from its power source.

 

Contact your 

    supplier. 

 

There is no proper handshaking with the     

    host system. Switch the host system on 
    and check connection and communication
   settings.  

 

The laser is not functioning. The laser is 

   defect. Contact your supplier. 

■ 

The ambient temperature is too high. Make

   sure the scanner has enough air ventilation
   and is not placed in direct sunlight.

Problem

Pollux manual deel_2  03-11-2000 10:32  Pagina 34

Summary of Contents for MaxiScan 2300









































Reviews: