background image

 

6 / 7 

 

P/N R466-5569-

EN • REV B • DRAFT A03 

Sensor/repeater removed 

 

Specifications 

Compatibility 

UTC Fire & Security 
433 MHz Transmitter 
Range 

Input power 

100 to 230 VAC  

Power supply type 

Type A 

Mains frequency 

50 to 60 Hz 

Current consumption 

11.0 to 24.2 mA 

Wireless operating frequency: 

 

 

63bit 

433.92 MHz  

 

80+ LoNa 

433.65 MHz  

Allocated frequency band 

433.05 to 434.79 MHz 

Maximum power output 

10 dBm 

Operating temperature 

0 to +40°C  

Maximum relative humidity 

80% noncondensing 

Repeater dimensions (L x W x D) 

102 x 102 x 33 mm 

Battery type 

3.6 V, 3200 mAh lithium 

Samsung INR18650-35E, 
Panasonic NCR18650B 

Minimum energy level of the battery in its 
charged state 

87% 

Battery low threshold 

3.4 V 

Battery deep discharge protection level 

Note: 

Below this value battery is 

considered as short circuited and not 
charged. 

2.5 V 

Battery included 

18650 Li-ion battery cell 

Total equipment weight 

< 1 kg 

Indoor use only. 

Regulatory information 

Manufacturer 

UTC Fire & Security Americas Corporation, Inc. 
3211 Progress Drive, Lincolnton, NC, 28092, USA 

Authorized EU manufacturing representative: 
UTC Fire & Security B.V. 
Kelvinstraat 7, 6003 DH Weert, Netherlands 

Warnings and 
Disclaimers 

 

THESE PRODUCTS ARE INTENDED FOR SALE 
TO AND INSTALLATION BY QUALIFIED 
PROFESSIONALS. UTC FIRE & SECURITY 
CANNOT PROVIDE ANY ASSURANCE THAT 
ANY PERSON OR ENTITY BUYING ITS 
PRODUCTS, INCLUDING ANY “AUTHORIZED 
DEALER” OR “AUTHORIZED RESELLER”, IS 
PROPERLY TRAINED OR EXPERIENCED TO 
CORRECTLY INSTALL FIRE AND SECURITY 
RELATED PRODUCTS. 

For more information on warranty disclaimers and 
product safety information, please check 
https://firesecurityproducts.com/policy/product-
warning/ o
r scan the QR code. 

Version 

This document applies to the following firmware 
version or higher: 201 

Certification 

 

 

EN 50131-3, EN 50131-5-3, EN 50131-6 

Security Grade 2, Environmental class II 

Tested and certified by Telefication B.V. 

INCERT 

C-001-1503 

T031+A1 

European Union 
directives 

UTC Fire & Security hereby declares that this 
device is in compliance with the applicable 
requirements and provisions of all applicable rules 
and regulations, including but not limited to the 
Directive 2014/53/EU. For more information see: 
firesecurityproducts.com 

 

This product may contain a battery that cannot be 
disposed of as unsorted municipal waste in the 
European Union. See the product documentation 
for specific battery information. The battery is 
marked with this symbol, which may include 
lettering to indicate cadmium (Cd), lead (Pb), or 
mercury (Hg). For proper recycling return the 
battery to your supplier or to a designated 
collection point. For more information see 
recyclethis.info 

 

2012/19/EU (WEEE directive): Products marked 
with this symbol cannot be disposed of as 
unsorted municipal waste in the European Union. 
For proper recycling, return this product to your 
local supplier upon the purchase of equivalent 
new equipment, or dispose of it at designated 
collection points. For more information see: 
recyclethis.info 

Contact information 

firesecurityproducts.com or www.interlogix.com 
 

 

Summary of Contents for RF-9011-07-1








Reviews: