4 / 20
P/N 146253999-
6 (ML) • REV D • ISS 07MAR19
Regulatory information
Manufacturer
PLACED ON THE MARKET BY:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
AUTHORIZED EU REPRESENTATIVE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
or scan the QR code.
Certification
UL/cUL
The product must be connected to a listed burglar
system compatible control unit or power supply
unit, which provides a minimum 4 hours of
standby power and has a voltage output between
10 and 15 VDC.
All wiring must be made according to National
Electrical Code, NFPA70, and CSA C22.1,
Canadian Electrical Code Part I, Safety Standards
for Electrical Installations.
Perform walk test at least one per year.
Use only a listed power-limited supply.
FCC
Note:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the
equipment and receiver
•
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced
radio/TV technician for help
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
IC
This Class B digital apparatus complies with
Canadian ICES-003.
European Union
directives
UTC Fire & Security hereby declares that this
device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com.
For customer support, see www.interlogix.com/customer-
support.
DA: Installationsark
Introduktion
EV1012PI er en PIR-rumdetektor med dyrevenlig optik.
Installationsvejledning
Den anvendte teknologi i disse detektorer er modstandsdygtig
over for falske alarmer. Undgå imidlertid mulige årsager til
ustabilitet (se Figur 1), f.eks.:
•
Direkte sollys på detektoren
•
Kraftig træk på detektoren.
•
Varmekilder inden for detektorens synsfelt
•
Dyr over 35 cm i detektorens synsfelt (Figur 7)
•
Blokering af detektorens synsfelt med store genstande
som f.eks. møbler
Installation af detektoren
Figur 8 symbolforklaring
1.
Standardtilslutning
(fabriksstandard)
2.
Dobbelt sløjfe-tilslutning
CP Central
WT Gangtest
Sådan installeres detektoren:
1.
Tag dækpladen af og fjern skruen (se Figur 2, pkt. 1).
2.
Åbn forsigtigt detektoren med en skruetrækker (Figur 2,
pkt. 2 og 3).
3.
Gør soklen fast til væggen mellem 2,3 m og 3,0 m fra
gulvet. Til fladmontering anvendes mindst to skruer
(DIN
7998) i position A. Til hjørnemontering anvendes
skruer i position B eller C (Figur 3).
4. Tilslut detektoren (se figur 3 og 8).
5.
Vælg de ønskede jumper-indstillinger (se figur 6). Se
“Jumper-indstillinger” på side 5, hvis du ønsker yderligere
oplysninger.
6.
Fjern afskærmningen og påsæt klæbemærker efter behov
(se eksempel i Figur 5).
