background image

 

P/N 466-

 

 

5 / 6 

Set Date/Time 

On the System Programming screen, touch the Set Date/Time 
button. Here you can set the Date and Time settings.  

 

When you press on a white text box, it will bring up a keypad to 
allow you to change that setting. 

Installer Programming Screen 

The system has a screen for the Installer or qualified 
technician. If you inadvertently see the following screen, touch 
the 

press and hold the top white bar for seven 

seconds to exit. 

 

Trouble Conditions 

 

Problem 

Actions/Solutions 

Low battery 
icon  

Indicates that the Concord 4 security panel backup 
battery is low. 

System 
trouble 

 

A yellow triangle over the settings on the Main screen 
means a trouble condition exists on the Concord 4 or 
touch devices. Depending on volume settings and 
system configuration, four audible beeps (once a 
minute) may be heard. 

To check status, press the 

 icon. Then press the 

status icon.  

Note

: By pressing the 

 icon, if audible beeps are 

heard they will be suppressed for a minimum of four 
hours. 

If there is no trouble detailed after the status button is 
pressed, refer to the event buffer in the touch screen 
and/or view full status on an alphanumeric keypad 
connected elsewhere in the system. 

Status LED (Blue light) 

The touch screen has an LED that indicates power and sleep 
mode status at a glance. The table below explains LED 
behavior.  

Table 1: Status LED 

LED 

System status 

Solid blue (while backlights are on) 

Primary power present 

Fading blue 

Primary power failure 

Off 

Screen saver active 

Cleaning 

If necessary, use a soft cloth to clear smudges on the touch 
screen. Do not use glass cleaner. 

Maintenance and support 

A qualified technician should check this system every 3 years.  

Disposal

 

Dispose of the touch screen in accordance with local 
regulations. 

Warranty Information 

MANUFACTURER HEREBY DISCLAIMS ALL WARRANTIES 
AND REPRESENTATIONS, WHETHER EXPRESS, IMPLIED, 
STATUTORY OR OTHERWISE INCLUDING (BUT NOT 
LIMITED TO) ANY WARRANTIES OF MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR PURPOSE WITH 
RESPECT TO ITS CONCORD 4 PRODUCTS AND RELATED 
SOFTWARE. MANUFACTURER FURTHER DISCLAIMS ANY 
OTHER IMPLIED WARRANTY UNDER THE UNIFORM 
COMPUTER INFORMATION TRANSACTIONS ACT OR 
SIMILAR LAW AS ENACTED BY ANY STATE. 

(USA only) SOME STATES DO NOT ALLOW THE 
EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE 
EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY 
GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY 
ALSO HAVE OTHER LEGAL RIGHTS THAT VARY FROM 
STATE TO STATE. 

MANUFACTURER MAKES NO REPRESENTATION, 
WARRANTY, COVENANT OR PROMISE THAT ITS 
SECURITY PRODUCTS AND/OR RELATED SOFTWARE (I) 
WILL NOT BE HACKED, COMPROMISED AND/OR 
CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE 
ADEQUATE WARNING OR PROTECTION FROM, BREAK-
INS, BURGLARY, ROBBERY, FIRE; OR (III) WILL WORK 
PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS. 

Summary of Contents for Concord







Reviews: