Intergraph InterServe 05 Setup Setup Manual Download Page 58

Page: 58 / 75

System hangs after BIOS initializes

Reason

Solution

Incorrect memory speed set in the BIOS.

Change the “Installed Memory Speed,”
parameter under Chipset in AMIBIOS
Setup to 60 ns. See Chapter 3.

One or more processors is not active

Reason

Solution

The voltage regulator module for the CPU
is not correctly installed.

Open the base unit and reseat the voltage
regulator modules.

Does not boot from expected boot device

Reason

Solution

Boot sequence is incorrectly set.

Change the “System Boot Up Sequence”
parameter under Advanced in AMIBIOS
Setup. See Chapter 3.

Operating system not on the system drive.

Install the operating system as described in
Chapter 5.

Does not boot from floppy disk drive (drive A)

Reason

Solution

Corrupt boot diskette, or boot diskette does
not have correct boot utilities.

Replace the boot diskette.

Boot sequence is incorrectly set.

Change the “System Boot Up Sequence”
parameter under Advanced in AMIBIOS
Setup. See Chapter 3.

Corrupt BIOS.

Reprogram the BIOS using the Flash
Program Utility. See Chapter 3.

Summary of Contents for InterServe 05 Setup












































































Search results

Summary of Contents for InterServe 05 Setup

Reviews:

Related manuals for InterServe 05 Setup

Brands by name

Popular brands

Intergraph InterServe 05 Setup, Setup Manual

Search results

Summary of Contents for InterServe 05 Setup

Reviews:

Related manuals for InterServe 05 Setup

Brands by name

Popular brands