background image

36

IntelliTouch Personality Kit Installation Guide

Glossary

Expansion Kit: 

A kit that includes additional auxiliaries to an existing Personality Kit. Requires a

Load Center for each Expansion Kit.

Feature Circuits:

 Programmable circuits that may control relays and/or valve actuators. For details,

see the IntelliTouch Systems User’s Guide (P/N 520102)

High Voltage Compartment: 

Large lower right compartment of Load Center for all high voltage

wiring including circuit breakers, relays, and GFCI.

Indoor Control Panel: 

This 14 button remote controller with LCD (liquid crystal display) is wired to

the Personality board in the Power/Load Center. The control panel can be wall mounted inside a
house to control IntelliTouch Systems.

iS4:

 Four function Spa-Side remote. Can be spa wall or deck mounted.

iS10:

 Up to ten function spa-side remote with temperature changing capability. Can be spa wall or

deck mounted.

Load Center

: Metal enclosure with power relays, transformer, and circuit breakers. The Load Center

is Installed prior to Personality Kit installation. Used for distributing power for controlling IntelliTouch
Systems. Also known as the “sub-panel.”

Low Voltage Compartment:

 Top compartment of Load Center for all low voltage wiring.

Low Voltage Raceway:

 Vertical space in the left side of Power/Load Center for low voltage cabling.

MobileTouch Controller:

 Wireless controller for the IntelliTouch Systems with all the functionality of

the Indoor Control Panel.

Mud Box:

 Enclosure to provide mounting features for iS10 spa-side remote that is cast into gunite,

concrete, or other spa wall/deck construction.

Outdoor Control Panel:

 Control panel with flexible hinge installed in upper portion of Power/Load

Center to control IntelliTouch systems.

Personality Board:

 The circuit board mounted on top of the Outdoor Control Panel motherboard.

The Personality board defines the system capabilities.

Personality Kit:

 Set of parts to define the capability of a system; may include: Outdoor Control

Panel, temperature sensors, actuators, control panel (Indoor or MobileTouch), additional relays,
actuators.

Power Center:

 Same as Load Center with the exception of the circuit breaker base.

Relay Circuits:

 The circuits that control the relays on the Personality Board. Connectors on top

edge of the circuit board.

Screw Terminal  Connector:

 Removable connector that may attach to circuit board with multiple

sockets (anywhere from 2 to 12) to receive wires from controllers and sensors; wires held by screw
terminals; multiple wires of a small enough gauge (usually 22 AWG) may be coupled to a single
socket of a terminal connector.

Transceiver:

 Circuit board with attached antenna that can send and receive radio frequency

(wireless) transmissions. Used with the MobileTouch wireless controller.

Summary of Contents for Pool and Spa Control System















































Reviews: