Intellinet 561099 User Manual Download Page 2

Page: 2 / 45

8‐Port Gigabit Web‐Smart Switch

2 |

P a g e

FCC Certifications

This Equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received; including interference that may cause undesired operation.

CE Mark Warning

This equipment complies with the requirements relating to the EMC Directive

2004/108/EC and 2014/30/EU, the Low Voltage Directive 2006/95/EC and

2014/35/EU, and the RoHS Directive 2011/65/EU.

Intellinet has an on‐going policy of upgrading its products and it may be

possible that information in this document is not up‐to‐date. Please check with your local distributors for

the latest information. No part of this document can be copied or reproduced in any form without written

consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Summary of Contents for 561099













































Search results

Summary of Contents for 561099

Reviews:

Intellinet 561099, User Manual, Page: 2 / 45

Search results

Summary of Contents for 561099

Reviews: