background image

LSU80A : Load Support Unit

Operators Manual

 8 PRODUCT WARRANTY

Your Intelligent Charging Limited product is guaranteed against faulty workmanship materials
and malfunction for a period of 12 months from the date of purchase, unless agreed otherwise
by Intelligent Charging Limited. Within this warranty period Intelligent Charging Limited will
undertake to repair or replace the product proved to be faulty.

We recommend you keep all packaging for the duration of the 12 month warranty, after which
you should dispose of all waste packaging in accordance with your local legislation 

Products which have become faulty within the 12 month warranty period must be returned to
Intelligent   Charging   Limited,   where   Intelligent   Charging   Limited   will   then   investigate   the
warranty claim.

Intelligent   Charging   Limited   products,   when   properly   used,   will   render   excellent   service.
Therefore, users must read the User Manual and any other literature supplied with the product
carefully, and fully comply with all procedures shown in the literature and product training /
familiarisation   sessions,   as   misuse   or   failure   to   follow   the   instructions   may   render   this
warranty void.

This   warranty   is   not   transferable   and   excludes   routine   maintenance,   consumables,   parts
subject to normal wear and tear, service maintenance kits and damage caused by misuse or
negligence. Warranty claims attributable to improper, or careless, use or handling, and to
normal wear, are excluded from this warranty.

Intelligent Charging Limited only obligation shall be to repair or replace such products that
have proved to be faulty. Intelligent Charging Limited shall not be liable for any injury, loss or
damage, direct or consequential, arising out of the use, or the inability to use the product. The
customer shall determine the suitability of this  product for its intended use, and the customer
assumes all risks and liability whatsoever in connection herewith.

Intelligent Charging Limited reserves the right to improve or modify this product

without prior notice.

Doc: DWG1061-11-R2 LSU80A Operators manual.odt

Page 16 of 17

Copyright Material of Intelligent Charging Limited © 2018

Printed On : 17/07/19

Summary of Contents for LSU80A


















Reviews: