background image

 

 

 

Battery Compartment:

 

 

The IR-301’s batteries are self-contained.  Slide the rubber boot off the back 
of the sensor and replace the batteries with 2 each CR1225 Lithium 
Batteries.   These should power the IR-301 for approximately 2-3 weeks 

depending on the number of sensor activations.  When not using the sensor, 
you can disconnect the power by slipping a small piece of plastic between 

the + lead and the top battery.

 

 

Red LED:

 

 

The 

RED LED

 

is an alarm indicator.  It only illuminates when an alarm 

occurs during the first 10 minutes to aid in the initial set up and will 

automatically turn off after 10 minutes for covert reasons. 
 

Antenna:

 

 
The flexible stainless 

ANTENNA

 allows for the UHF propagation of the RF 

signal.  The 

ANTENNA

 must be oriented in a vertical direction for best RF 

propagation and for proper alignment of the infrared beams. 

 

Lens:

 

 

The IR-301’s focal length is preset to detect a person at an optimum 

distance of 20 feet, although it will work satisfactorily over a range of 5 to 
30 feet.  Its field of view is about 6 feet wide at a distance of 30 feet.  The 

LENS

 is aimed in the direction of your target area. 

 

 

 

 

 

 
 

 

 

 
 
 

 

 
 

 

 

 

Summary of Contents for PPK-3 KIT












Reviews: