Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 79

Page: 79 / 162

Intel

Server System SR2612UR Service Guide

9. Remove the four screws from the power distribution module and lift the power

distribution module from the server system as shown below.

Figure 68. Remove the four screws from the PDB

10. Install the replacement power distribution module.

Installing Power Distribution Module

1. Install power distribution module onto spacers and Install all four screws as shown

below.

Figure 69. Installing the Power Distribution Module

2. Route cable marked “P4” through the cable chase fan blank as shown below.

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands