Intel SE7221BA1 Technical Manual Download

Page: 38 / 77

Input Output Subsystem

Intel® Entry Server Board SE7221BA1-E TPS

Revision

1.5

Green LED

Green/Yellow LED

OM16513

NIC 1 NIC 2

•

Compliant to 802.3x flow control support

•

Jumbo

frame

support

•

TCP, IP, UDP checksum offload

•

Automatic

MDI/MDIX

crossover

•

Full device driver compatibility

•

Configuration EEPROMs that contain the MAC address and ASF 2.0 support

•

Wake On LAN technology power management support

•

PCI Express* Active State Power Management Support (L0s)

•

ASF 2.0 support

5.2.2

Intel® 82551QM Integrated 10/100 LAN controller

The Intel® 8255QM Fast Ethernet controller provides the following functions:

•

Basic 10/100 Ethernet LAN connectivity

•

IEEE 802.3 10Base-T and 100Base-TX Compatible PHY

•

IEEE 802.3x 100Base-TX Flow Control Support

•

IEEE 802.3u Auto-Negotiation support

•

TCP, IP, UDP checksum offload

•

Full device driver compatibility

•

Wake On LAN technology power management support.

•

Wired for management

5.2.3

RJ-45 LAN Connector with Integrated LEDs

Two LEDs are built into the RJ-45 LAN connectors (as shown in Figure 11).

Table 11 describes the LED states when the board is powered up and the Gigabit LAN
subsystem is operating.

Figure 11. LAN Connector LED Locations

Summary of Contents for SE7221BA1














































































Search results

Summary of Contents for SE7221BA1

Reviews:

Related manuals for SE7221BA1

Brands by name

Popular brands

Intel SE7221BA1, Technical Manual

Search results

Summary of Contents for SE7221BA1

Reviews:

Related manuals for SE7221BA1

Brands by name

Popular brands