Intel H2000WP Service Manual Download Page 7

Page: 7 / 88

Table of Contents

Intel

Server System H2000WP Family Service Guide

vii

Table of Contents

Safety Information

............................................................................................... iii

Preface

................................................................................................................. v

Server System Features

.................................................................................... 1

Server System Feature Overview

.................................................................................................. 1

Server System Components

.......................................................................................................... 3

Front Panel

.................................................................................................................................. 5

Back Panel

.................................................................................................................................. 6

Server Board Components

............................................................................................................ 7

Intel

Light-Guided Diagnostics

................................................................................................... 8

System Jumpers

........................................................................................................................... 9

Hard Disk Drive Carriers ................................................................................................ 10

Bezel 10

Hot-Swap SAS/SATA Backplane .................................................................................. 10

Advanced Management Options ................................................................................... 12

Dummy Tray Cover ........................................................................................................ 13

Hardware Installations and Upgrades

............................................................. 14

Before You Begin

...................................................................................................................... 14

Tools and Supplies Needed .......................................................................................... 14

System Reference ......................................................................................................... 14

Cable Routing

........................................................................................................................... 14

For cable connection inside Node tray .......................................................................... 15

Removing and Installing the Front Bezel

..................................................................................... 15

Removing the Front Bezel ............................................................................................. 15

Installing the Front Bezel ............................................................................................... 15

Removing and Installing the System Top Cover

.......................................................................... 16

Removing the System Top Cover.................................................................................. 16

Installing the System Cover ........................................................................................... 17

Removing and Installing the Compute Node Tray

........................................................................ 17

Removing the Node Tray ............................................................................................... 18

Installing the Node Tray ................................................................................................. 18

Removing and Installing the Redundant Power Supply Unit

......................................................... 18

Removing the Power Supply Unit .................................................................................. 19

Installing the Power Supply Unit .................................................................................... 19

Removing and Installing the Node Tray Air Duct

........................................................................ 19

Removing the Air Duct ................................................................................................... 20

Installing the Air Duct ..................................................................................................... 20

Transparent Mylar Installation ....................................................................................... 21

Removing and Installing Processor

............................................................................................. 22

Removing Processor Heatsink(s) .................................................................................. 22

Installing the Processor ................................................................................................. 22

Installing Processor Heatsink(s) .................................................................................... 24

Removing the Processor ............................................................................................... 25

Installing and Removing Memory

............................................................................................... 25

Installing Memory ........................................................................................................... 25

Summary of Contents for H2000WP

























































































Search results

Summary of Contents for H2000WP

Reviews:

Related manuals for H2000WP

Brands by name

Popular brands

Intel H2000WP, Service Manual

Search results

Summary of Contents for H2000WP

Reviews:

Related manuals for H2000WP

Brands by name

Popular brands