Intel D946GZTS - Desktop Board Motherboard Page 21 Product Manual Download | Manualshive

Page: 21 / 76

background image

Desktop Board Features

21

The desktop board supports the

PCI Bus Power Management Interface Specification

.

Add-in cards that support this specification can participate in power management and
can be used to wake the computer.

+5 V Standby Power Indicator LED

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.

The desktop board’s standby power indicator, shown in Figure 3, is lit when there is
standby power still present on the board even when the computer appears to be off.
For example, when this LED is lit, standby power is still present at the memory module
sockets and the PCI bus connectors.

Figure 3. Location of Standby Power Indicator

«
...
19
20
21
22
23
...
»

Summary of Contents for D946GZTS - Desktop Board Motherboard













































































Reviews:

No comments

Related manuals for D946GZTS - Desktop Board Motherboard

Brand: Yanmar Pages: 44

1stMainboard VG33

Brand: FIC Pages: 38

Brand: MINN KOTA Pages: 14

Brand: Infineon Pages: 24

Brand: JETWAY Pages: 37

Brand: Texas Instruments Pages: 19

Brand: Microchip Technology Pages: 44

Brand: WynMax Pages: 68

Brand: MSI Pages: 77

Brand: DFI Pages: 139

Brand: Analog Devices Pages: 14

Brand: ASROCK Pages: 199

Brand: Raspberry Pi Pages: 13

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands