background image

Desktop Board Description 

21 

 

For information about  

Refer to 

The 

PC Serial Presence Detect Specification 

Section 1.3, page 16 

Obtaining copies of PC SDRAM specifications 

http://www.intel.com/design/pcisets/memory  

1.6 Intel

®

 810E2 Chipset 

The Intel 810E2 chipset consists of the following devices: 

• 

82810E DC-133 Graphics Memory Controller Hub (GMCH) with accelerated hub architecture 
(AHA) bus 

• 

82801BA I/O Controller Hub (ICH2) with AHA bus 

• 

SST 49LF004A 4 Mbit firmware hub (FWH) 

The GMCH is a centralized controller for the system bus, the memory bus, the AGP bus, and the 
Accelerated Hub Architecture bus.  The ICH2 is a centralized controller for the board’s I/O paths.  
The FWH provides the nonvolatile storage of the BIOS.  The component combination provides the 
interfaces as shown in Figure 3.  

810E2 Chipset

82801BA I/O Controller

Hub (ICH2)

82810E

Graphics Memory

Controller Hub

(GMCH)

SST 49LF004A

Firmware Hub

(FWH)

100 MHz

SDRAM

Bus

AHA

Bus

ATA-66/100

USB

66/100/133 MHz

System Bus

AC Link

LPC Bus

Digital

Video Output

OM11132

CSMA/CD

Unit Interface

Display

Interface

SM Bus

PCI Bus

 

Figure 3.  Intel 810E2 Chipset Block Diagram

 

For information about  

Refer to 

The Intel 810E2 chipset 

http://developer.intel.com 

The resources used by the chipset 

Chapter 2 

The chipset’s compliance with ACPI, APM, AC ‘97 

Section 1.3, page 16 

Summary of Contents for D810E2CA3

















































































































Reviews: