Intel 80331 Design Manual Download Page 61

Page: 61 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.15

PCI 66 MHz Embedded Topology

Figure 30

and

Table 22

provides routing details for a topology with for an embedded PCI 66 MHz

design.

Trace Length TL_AD1, TL_AD2 from connector to
receiver

0.75” minimum - 1.5”
maximum

1.75” minimum - 2.75”
maximum

Length Matching Requirements

No length matching is required among datalines. For
length matching for clocks, refer clock guidelines

Table 8

Number of Vias

Four vias maximum

Table 21.

PCI 66 MHz Slot Table (Sheet 2 of 2)

Parameter

Routing Guideline for AD

Bus

Routing Guideline for

Upper AD Bus

Figure 30.

PCI 66 MHz Embedded Topology

Table 22.

PCI 66 MHz Embedded Table (Sheet 1 of 2)

Parameter

Routing Guideline for AD Bus

Reference Plane

Route over an unbroken ground plane

Breakout

5 mils on 5 mils spacing. Maximum length of the
breakout is 500 mils.

Motherboard Trace Impedance (microstrip and
stripline)

50 Ohms +/- 15%

Add-in card Impedance (microstrip and stripline)

60 Ohms +/- 15%

Stripline Trace Spacing

10 mils, from edge to edge

Microstrip Trace Spacing

15 mils, from edge to edge

Group Spacing

Spacing from other groups: 25 mils minimum edge to
edge

TL 1

_EM

T L2

TL_E

EM 1

E M 3

E M 4

L_E

EM 2

Summary of Contents for 80331





















































































































































Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands

Intel 80331, Design Manual

Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands