14.26-4
2300-MULTI Specifications.
RTD Inputs:
-Input Points
2
-RTD Configuration
2 or 3 Wire
-Resolution
0.1°C
-Drift
100ppm/°C
Typ.
-Line resistance effect < 0.1°C balanced
-Max. line resistance 100ohms
-Isolation
1500Vrms
between
field
and
logic
RTD Type:
-Number
Type
Range
Accuracy
-1
PT100
-200
to
850°C
±
0.3°CIEC
751:1983
-2
Ni120
-80
to
320°C
±
0.3°C
-3
PT1000
-200
to
850°C
±
0.3°C
-4
Ni1000-DIN -200
to
850°C
±
0.3°C
-5
Ni1000-Landys&Gyr
-200
to
850°C
±
0.3°C
-6
Ohms
10
-
400
ohms
±
0.05%
-7
Ohms
100-4000ohms
±
0.05%
Current Inputs:
-Input
Points
2
-Input
Current
0(4)~20
mA
-Input
Resistance
250ohms
-Drift
100ppm/°C
-Input
Type
Range
Resolution
-1
0
–
4095
12
bits
-2
4~20.000mA
1uA
-3
+/-20.000mA
1uA
-Accuracy
0.2%
of
span
-Isolation
1000Vrms
between
field
and
logic
Factory Option : Voltage Inputs:
-Input Voltage
0~1 Vdc or 0~10 Vdc
-Input Resistance
190kohms
-Input
Type
Range
Resolution
-4
0
–
4095
12
bits
-5
0
–
10.000
V
1mV
-6
+/-
10.000
V
1mV
-7
0
–
1.0000
V
0.1mV
-8
+/-
1.0000
V
0.1mV
-Drift
100ppm/°C
-Accuracy
0.2%
of
span
-Isolation
1000Vrms
between
field
and
logic
Current Output:
-Output
Points
1
-Output
Current
0(4)~20
mA
-Output
Type
Range
Resolution
-1
0
–
4095
12
bits
-Drift
100ppm/°C
-Accuracy
0.05%
of
span
-Compliance
1000 ohms max. @ 24Vdc
500 ohms max. @ 12Vdc
Factory Option : Voltage Output:
-Output
Voltage
0(2)~10
V
-Output
Type
Range
Resolution
-2
0
–
4095
12
bits
-Drift
100ppm/°C
-Accuracy
0.05%
of
span
-Compliance
2000
ohms
min.
Load
Digital Inputs:
-Input Points
4
-Input Voltage Range 10~26 Vdc
-Input Current per input
4mA@12Vdc / 8mA @24Vdc
Counters:
-Inputs
1
to
4
-Resolution
32
Bits
-Frequency
50
Hz
(max)
-Pulse
Width
20
ms
(min)
Digital Outputs:
-Output
Points
2
-Maximum
Voltage
36
Vdc
-Maximum Current
100 mA per output
-Vceon
1.1V Max.
Isolation:
-Between field and logic
1500Vrms between field and logic
Connectors:
-Logic Power and Comms
4 Pin plug-in connector on side of station
-Inputs
18
Way
screw
plug-in
connector
on
top
of
station
Comms:
-Protocols
RS485,
Modbus
RTU.
-Baud
Rate
9600.
-Format
8 bit, No Parity, 1 Stop.
Power Supply:
-Logic Supply Voltage 12~24 Vdc
-Logic Supply Current 87mA @ 12V / 45mA @ 24V
Safety and EMC Compliances:
EMC Compliance
89/336/EEC and Low Voltage Equipment Directive 73/23/EEC.
Safety
Compliance
IEC
950.
General Specifications:
(Unless otherwise stated in other input specifications.)
Operating Temperature
-10~50˚C.
Storage
Temperature
-40~85˚C.
Operating Humidity
Up to 95% non condensing.
Housing
-Dimensions L=97.5,
W=22.6,
H=109mm. -Mounting
35mm
Symmetrical Mounting Rail.
Note 1.
Contact INTECH INSTRUMENTS for more detailed programming information.
Product Liability.
This information describes our products. It does not constitute guaranteed properties and is not intended to affirm the
suitability of a product for a particular application. Due to ongoing research and development, designs, specifications, and documentation are
subject to change without notification. Regrettably, omissions and exceptions cannot be completely ruled out. No liability will be
accepted for errors, omissions or amendments to this specification. Technical data are always specified by their average values and are based
on Standard Calibration Units at 25C, unless otherwise specified. Each product is subject to the ‘Conditions of Sale’.
Warning: These products are not designed for use in, and should not be used for patient connected applications. In any critical
installation an independent fail-safe back-up system must always be implemented.