Intec Controls MSR ELECTRONIC PolyGard AT-1110, User Manual

Share

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

Page: 8 / 17

Intec Controls MSR ELECTRONIC PolyGard AT-1110 User Manual Download Page 8

Customer Services (858) 578-7887 & (888) GO IN

TEC

IN

TEC

Controls, 12700 Stowe Dr., Suite 1

0

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 141114

Polygard® is a registered trademark of MSR

AT-1110V3

PolyGard

®

CO Transmitter

User Manual - AT-1110 V3

Page 08



 
The two relays are activated in dependence of the gas concentration. If the gas concentration exceeds the

adjustedalarmthreshold,thecorrespondingrelayswitcheson.Ifthegasconcentrationfallsbelowthethreshold

minushysteresis,therelayswitchesoffagain.
The contact function for relay 2, NC (normally closed) or NO (normally open), can be selected via the jumper

NO/NC.Seefig1and3.Relay1isequippedwithachangeovercontact.
ViatheModBusinterfacethetwoalarmthresholdsandthehysteresisarefreelyadjustableatthePCwithinthe

measuringrange.Theprocedurecanbereadfromtheusermanual“ModBusSoftware”.
Thefollowingparametersarefactoryset.
Alarmthreshold1=Relay1: 50ppm
Alarmthreshold2=Relay2: 100ppm
Switchinghysteresis:   15ppm





Specifications subject to change without notice. | USA 141114 | Page 8 of 17

Polygard® is a registered trademark of MSR | AT-1110V3

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110_V3 – UserManual

Specifications subject to change without notice. | USA 160104 | Page 8 of 17

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110 V3 – UserManual

PolyGard

®

is a registered trademark of MSR-Electronic GmbH | AT-1110V3

«
...
6
7
8
9
10
...
»

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110


















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands