Intec Controls MSR ELECTRONIC PolyGard AT-1110, User Manual

Page: 4 / 17

Customer Services (858) 578-7887 & (888) GO IN TEC
IN TEC Controls, 12700 Stowe Dr., Suite 1 0 0, Poway, CA 92064
Fax (858) 578-4633 & (888) FX IN TEC
www.inteccontrols.com
Specification subject to change without notice.
Printed in USA 141114
Polygard® is a registered trademark of MSR AT-1110V3
PolyGard
®
CO Transmitter
User Manual - AT-1110 V3
Page 04

 
 
Avoid any force (e.g. by thumb) on the sensor element during operation or installation. Electronics can be
destroyedbystaticelectricity.Therefore,donottouchtheequipmentwithoutawriststrapconnectedtogroundor
withoutstandingonaconductivefloor.
 
Whenchoosingthemountingsitepleasepayattentiontothefollowing:
• Thespecificweightofcarbonmonoxideisasmallerthanthatofair(factor0.97).
Recommendedmountingheightis1.5m(5feet)to1.8m(6feet)abovefloor.
• Choosemountinglocationofthesensoraccordingtothelocalregulations.
• Considertheventilationconditions!Donotmountthetransmitterinthecenteroftheairflow(airpassages,
suctionholes).
• Mountthetransmitteratalocationwithminimumvibrationandminimumvariationintemperature(avoid
directsunlight).
• Avoidlocationswherewater,oiletc.mayinfluenceproperoperationandwheremechanicaldamagemight
bepossible.
• Provideadequatespacearoundthesensorformaintenanceandcalibrationwork.
Ductmounting
• Mountonlyinastraightsectionofductwithminimumairvortex.Keepaminimumdistanceof1m(3,5feet)
fromanycurveorobstacle.
• Mountonlyinaductsystemwithamaximumairvelocityof10m/s(2000ft/min)orless.
• Mountingmustbeperformedsothattheprobeopeningsareinlinewiththeairflow.
 
• Openthecover.UnplugbasicPCBcarefullyfromthebottompart.
• Fixbottompartbyscrewsverticallytothewall(terminalblockstotheground).
• PluginthebasicPCBatX4andX5withcare.Replacethecover.
 
Considerstaticelectricity!See3.Mounting
• Installation of the electrical wiring should only be performed by a trained specialist according to the
connection diagram, without any power applied to conductors and according to the corresponding
regulations!
• Avoidanyinfluenceofexternalinterferencebyusingshieldedcablesforthesignalline,butdonotconnect
theshield.
• Recommended cable for analog mode: Belden Twisted Shielded (20 AWG), max. res. 73  /km (20.8
 /1000ft).
• ItisimportanttoensurethatthewireshieldsoranybarewiresdonotshortthemountedPCB.
Specifications subject to change without notice. | USA 141114 | Page 4 of 17
Polygard® is a registered trademark of MSR | AT-1110V3
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN TEC | relevantsolutions.com/inteccontrols
AT-1110_V3 – UserManual
Specifications subject to change without notice. | USA 160104 | Page 4 of 17
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN TEC | relevantsolutions.com/inteccontrols
AT-1110 V3 – UserManual
PolyGard ® is a registered trademark of MSR-Electronic GmbH | AT-1110V3