Intec Controls MSR ELECTRONIC PolyGard AT-1110 User Manual Download Page 10

Page: 10 / 17

Customer Services (858) 578-7887 & (888) GO IN

TEC

Controls, 12700 Stowe Dr., Suite 1

0, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 141114

Polygard® is a registered trademark of MSR

AT-1110V3

PolyGard

CO Transmitter

User Manual - AT-1110 V3

Page 10



 

 







Jumper020%notset

Checkjumperposition

Powervoltagenotapplied

MeasuretensionatX4:

Twowire:Pin1(+)and4()

Threewire:Pin1(+)and2()

PCBAT1110notpluggedincorrectlyat

X4andX5

ReplugPCBcorrectly

Outputsignal<3mA/1.5V

and/orcontrolvoltage<30mV

onlyforstartingsignal2V/4mA



Wirebreak

Checkthewiring

Outputsignal>22mA/220mV Shortcircuit

Checkthewiring

Sensorelementnotcalibrated

Calibratesensorelement

Controlvoltagedoesnotreach

thecalculatedvalue

Sensorsensitivity<30%

Replacesensorelement

Powervoltagenotapplied

MeasuretensionatX4

Noreactionoftheoutputsignal

inspiteofgasconcentration

Signal(Pin4)notwiredcorrectly

Checkthewiring



 

ThecrosssensitivitydependsontheusedtransmittertypeandcanbereadfromthetableTechnicalData(see9.).

Othergasescanhaveaninfluenceonthesensitivity,too.Thetabledoesnotclaimtobecomplete.Theindicated

sensitivitydataareonlystandardvaluesreferringtonewsensorelements.

Specifications subject to change without notice. | USA 141114 | Page 10 of 17

Polygard® is a registered trademark of MSR | AT-1110V3

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110_V3 – UserManual

Specifications subject to change without notice. | USA 160104 | Page 10 of 17

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

| relevantsolutions.com/inteccontrols

AT-1110 V3 – UserManual

PolyGard

is a registered trademark of MSR-Electronic GmbH | AT-1110V3

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110


















Search results

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110

Reviews:

Brands by name

Popular brands

Intec Controls MSR ELECTRONIC PolyGard AT-1110, User Manual

Search results

Summary of Contents for MSR ELECTRONIC PolyGard AT-1110

Reviews:

Brands by name

Popular brands