IMPORTANT NOTE: In daily use you may use the boiler as soon as the water font button illuminates RED - BUT ON FIRST
INSTALLATION YOU SHOULD WAIT AT LEAST 10 MINUTES BEFORE STARTING TO USE THE WATER.
• Your machine will not fill completely at once. The water input is electronically controlled to obtain maximum output,
temperature and efficiency.
IN DAILY USE - switch on and wait for the water font push-button to illuminate RED, The water will then be at the correct
Temperature.
• To dispense hot water, place cup on drip-tray and press button.
7.0 - PROGRAM MODE
The LCD display in conjunction with the On/Off button gives access to the program menu which allows various settings to
be selected.
Most of the menus should not be accessed or changed because they are factory set, however, water volume (measured
vend) will need to be set, according to the cup-size and possibly water temperature may require alteration from factory
default setting.
To access the program menu:
• Switch the boiler off and back on again - within a few seconds of the boiler being switched on again, press and
hold the On/Off button in for approximately 10 seconds, until the display reads
“PROGRAM MODE”
.
• Continue to press On/Off button to proceed through menu selections until desired mode is reached.
• To select mode, hold button for 3 seconds.
PROGRAM MEASURED WATER VOLUME (VEND/F1):
Enter PROGRAM MODE as described above. Scroll through the menu until “PROGRAM VEND H/F1” is displayed - hold
button in for 3 seconds to select. Display will read “VEND H/F1” and number of seconds. Using the On/Off button to
increase the number of seconds, and the Eco button to decrease the number of seconds, set the Vend Time as desired.
When set, hold button in for 3 seconds to confirm. Continue scrolling through menu until “EXIT PROGRAM” is displayed -
push and hold button for 3 seconds to exit.
UCD47-2 (Two x Water Fonts) ONLY:
The UCD47-2 boiler is supplied with two independant water fonts, each of which can be set to deliver a different measured
volume. Set the first water font (VEND H/F1) as already described above then scroll through the menu to the next
selection (VEND C/F2). Repeat the instructions as above to set measured volume of second water font.
PROGRAM “ON DEMAND” WATER DISPENSE:
If preferred the water font can be configured to dispense water “on demand” instead of pre-set measured volumes:
Enter
“PROGRAM MODE”
as described above. Scroll through menu until
“PROGRAM VEND H/F1”
is displayed - hold
button in for 3 seconds to select. Display will read
“VEND H/F1”
and number of seconds. Push the
ECO
button to reduce
the number of seconds... continue pressing button until the display shows ZERO seconds (0.00) - hold button in for 3
seconds to confirm.
“EXIT PROGRAM”
as above. The boiler will now dispense “on-demand” e.g. push and hold the
button until desired volume of water has filled cup.
PROGRAM TEMPERATURE:
The boiler temperature is factory set to operate at around 97°C. This temperature can be adjusted in 1°C increments
between 80° and 99°C. Follow instructions as above, scrolling through menu until
“TEMP SET”
is reached - hold button
down for 3 seconds to select. Continue pushing button until desired temperature is displayed - push and hold button in for
3 seconds to set temperature. Continue to scroll through menu until
“PROGRAM EXIT”
is displayed - again push and hold
button for 3 seconds to exit program mode.
OTHER PROGRAM MENU OPTIONS:
NOTE: These are factory-set and generally do not need to be changed:
• M/C TYPE
- This allows the machine to be set between “under-counter” (UCDB series) and “counter-top” models.
(Factory-set to: under-counter). This would only need to be accessed if a new circuit board were fitted to the boiler.
• DRAIN TIME
- This is the time (in seconds) that the machine allows for the water (contained in water feed tube) to drain
back from the water font (factory-set at 3 seconds). This would only require adjustment if the counter-top font were
located more than 1 metre from the under-counter unit.
