background image

 

SAFETY INSTRUCTIONS 

 

Read the manual before use and installation and keep it for future reference. 

 

Assembly and placement of the device must be done on flat and firm surface. 

 

Keep a safety distance of at least 0.6 m from other objects. 

 

Check the product regularly for signs damage or wear. 

 

Do not modify the product. 

 

Ask your doctor for advice before starting an exercise program. 

 

Keep the device out of the reach of children and minors. 

 

Always warm up before use. 

 

Read all instructions and warnings before use. 

 

Before  starting  the  assembly,  check  that  all  parts  are  complete  and  undamaged.  Use  only 

original spare parts and accessories. Do not make unauthorized modifications to the product. 

 

Installation  may  only  be  performed  by  an  adult.  Prior  to  use,  make  sure  that  the  product  is 

correctly  assembled  and  properly  attached.  This  device  must  be  properly  assembled  and 
secured  to  prevent  injury  to  the  user.  If  the  device  does  not  work  properly,  shows  signs  of 
damage  or  wear,  stop  using  it  immediately.  Damaged  or  worn  parts  must  be  replaced 
immediately. 

 

Prior to use, make sure that all bolts and nuts are tight. If the product is damaged, do not use 

it. 

 

Exercise  sensibly  and  carefully,  do  not  overload.  Movements  must  not  be  abrupt  to  avoid 

injury. 

 

Do not hold your breath during exercise. 

 

Exercise  properly  and  appropriately.  Exercise  with  high  intensity  can  lead  to  health 

complications. 

 

Always wear sportswear and shoes. Keep all clothing and body parts away from moving parts. 

 

Adjustable parts must not prohibit the movement of the user.  

 

Improper  exercise  or  failure  to  follow  safety  precautions  can  result  in  serious  injury.  Wear 

appropriate sportswear, including sports shoes. 

 

Never exceed the specified weight limits.  

 

Pay  attention  to  your  body's  signals.  In  case  of  negative  physical  reactions,  stop  exercising 

immediately and contact your doctor. 

 

Before use, make sure that the cables are in the pulleys.  

 

If you are unsure of the anchoring, consult an expert for the correct anchoring. 

 

For indoor use only.  

 

Category:

 H for home use 

 

Load capacity: 

150 kg

 

 

Max. weights limit: 

90 kg

 

 

Product weight

: 72,8 kg 

 

 

Summary of Contents for BODYCRAFT IN 23288


















Reviews: