Unpack tap components.
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
Unscrew and remove threaded extension
from valve body.
Do not discard, as you
will need this later
(See Figure 1)
.
Leave small washers in place.
Feed tubes down through the hole in
the sink/counter until the base is at
rest. Set faucet at desired angle.
From under sink, slide 38mm fiber
washer over faucet base. Reinstall
threaded extension onto the base until
snug. Thread star nut onto extension
until snug (See Figure 2).
From under sink, slide 38mm fiber washer
over threaded extension. Thread star nut
onto extension until snug.
Attach the quick connector to the
ends of the copper tubes running
from the tap.
Install a
white
9.5mm tube into other end
of quick connector.
If sink/counter thickness exceeds 19mm
a hole diameter of 38mm
is required
.
An assistant may be needed to hold
the tap head in place
while securing the tap.
2
For a standard 38mm sink/counter hole
Feed tubes down through the hole in
the sink/counter until the base is at
rest. Set faucet at desired angle.
Large washer required for sink holes
larger
than 38mm or for porcelain sinks with
radius or beveled holes.
Before feeding tubes through sink
hole, remove extension. Place 33mm
large steel washer over threads on
faucet base. Reinstall extension.
Tap is factory-ready for installation
into a standard 38mm sink/counter hole.
32mm
Small
Steel
Washer
Fiber
Washer
Star Nut
33mm Large
Steel Washer
32mm
Small
Rubber
Washer
Standard 38mm hole
Hole larger than 38mm
Installing into hole smaller than 38mm
Figure 1
Figure 2
Property Damage:
Do not pinch or break copper
tubing. Do not distort the last 25mm of tubing.
32mm Small
Steel Washer
Fiber
Washer
Star Nut
32mm Small
Rubber Washer
32mm
Small
Steel
Washer
32mm
Small
Rubber
Washer
INSTALLING THE TAP
a
C
b
NOTICE
6
7
(1)
(2)
(3)
Select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
The tank should be within 400mm
or less of faucet water lines and
within 760mm or less of a standard
grounded outlet.
While holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Property Damage:
Tank must be located
within 400mm of faucet and within 760mm
or less of a standard grounded outlet. DO NOT
extend plumbing or electrical lines.
3
Without depressing the gray button,
place the snap-connect fitting at
the end of the
blue
6.4mm tube onto
the left fitting on the tank,
pushing until it clicks into place. (1)
Slip the flexible
white
11mm tube
over barbed middle fitting and slide
down approximately 12mm. (2)
Slip the
clear
8mm tube over
the far right smooth fitting and slide
down approximately 12mm. (3)
Visually check for pinched or
crimped tubes.
4
Property Damage:
Pinched or blocked water
lines may cause damage to the tank.
Check to make sure tubes are connected
properly and are pushed down as far as possible.
Tank must be
mounted level
to ensure
proper operation.
Hose clamps are not needed for any
of the connections.
Mount tank vertically in an area that
allows clearance on the underside of
the tank for drainage, if necessary.
DO NOT over tighten screws.
Pre-drill 3.2mm pilot holes at marks.
Turn screws into pre-drilled holes,
leaving 6.4mm exposed.
Hang the tank on the screws.
Tighten the screws with only 1/2
turn clockwise.
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
Leave 6.4mm for
hanging tank.
Brass Nut
Ferrule
Brass Insert
Wing Nut
Fiber
Washer
Brass Nut
Ferrule
Wing Nut
Fiber
Washer
1
2
3
Plastic
tube
MOUNTING THE TANK
CONNECTING TAP TO TANK
a
a
b
NOTICE
NOTICE
