background image

INSINGER MACHINE COMPANY LIMITED WARRANTY- COMMERCIAL MARINE USE

PART 1   TECHNICAL INFORMATION

®

GW_40TM09

www.insingermachine.com    800-344-4802

Labor will be billed to the customer at a reduced 
rate of $40.00 per hour. If sailing with a vessel is 
required, then an eight hour per day minimum will 
apply.

This limited warranty does not cover accident, 
abuse, misuse, alteration, misapplication, improper 
installation, 

fi

 re, 

fl

 ood, or improper maintenance 

or service, or failure to perform normal and routine 
maintenance as set out in the instruction booklet 
(operating instructions) or for improper operation 
or failure to follow normal operating instructions 
(as set out in the instruction booklet).

Insinger is not responsible nor liable for any 
conditions of erosion or corrosion caused by 
corrosive detergents, acids, lye or other chemicals 
used in the washing, caring and or cleaning 
process.

Warranty service must be done by either Insinger      
Appointed Service Agencies or agencies, custom-
ers galley engineers receiving prior authorization 
from Insinger.  

There are no other express warrants except as set     
forth herein and any applicable implied warranties 
of merchantability and 

fi

 tness are limited in 

duration to the period of coverage of this express 
written limited warranty. This limited warranty 
supersedes all other   express warranties, implied 
warranties of merchantability and 

fi

 tness or limited 

warranties as the above date.  

Insinger does not authorize any person or company  
locally or overseas to assume for it any other       
obligation or liability in connection with the sale, 
installation, use, removal, return or replacement   
of its equipment; and no such representations are 
binding on Insinger.

 

Insinger Machine Company, Inc. (Insinger) hereby     
warrants to the original retail purchaser of this 
Insinger Machine Company, Inc. product, that if it 
is assembled and operated in accordance with the 
printed instructions accompanying it (installation 
manual), then for a period of 15 months from 
the date of installation on board the vessel, that 
said Insinger product shall be free from defects in       
material and workmanship.  

Insinger may require reasonable proof of your 
date of equipment install, therefore, you should 
retain your copy of invoice or shipping document.

This limited warranty shall be limited to the 

        

replacement of parts which prove defective under 
normal use and service and which on examination 
shall indicate, to Insinger’s satisfaction, they are 
defective. Any part that   is claimed to be defective 
and covered by this limited warranty must be       
returned to Insinger. Furnish serial number of 

    

machine with shipment and send to:

Insinger Machine Company, Inc.
6245 State Road
Philadelphia, PA  19135-2996

If Insinger’s inspection con

fi

 rms the defect and 

the claim, Insinger will repair or replace such 
part without charge and return it to you freight or 
postage prepaid. If part damages are not covered, 
Insinger will contact the customer and advise.

If a factory trained authorized technician is 

         

required to repair or replace defective parts or 
material during  the 18 month warranty period, 
the cruise line will be responsible for the payment 
of travel expense and a  minimum of four hours 
labor. 

9

Summary of Contents for GW-40 BarMaster







































Reviews: