Insignia NS-DWH2BS8 Installation Manual Download Page 11 | Manualshive

Page: 11 / 24

background image

11

Top Control Dishwasher

www.insigniaproducts.com

Step 2: Adjust the leveling legs

1

Move the dishwasher close to the installation location and lay it on its back.

2

Measure the installation height and the dishwasher height.

3

Extend the leveling legs out from the dishwasher base 1/4 in. (6.35 mm) less than the installation height.

Step 3: Remove the toekick

•

Remove the two toekick screws with a Phillips screwdriver, then remove the toekick.

You’ll need:

Adjust to 1/4 in. (6.35 mm)
less than the installation
height.

Adjust to 1/4 in. (6.35 mm)
less than the installation
height.

Phillips screwdriver

Adjustable wrench

NS-DWH2_BS8_SS8_NS-DWR2_BS8_WH8_SS8_17-0649_Install MAN_V3_ENG.fm Page 11 Thursday, July 27, 2017 9:21 AM

«
...
9
10
11
12
13
...
»

Summary of Contents for NS-DWH2BS8

























Reviews:

No comments

Related manuals for NS-DWH2BS8

Brand: Gorenje Pages: 38

AdoraDish V2000

Brand: V-ZUG Pages: 52

Brand: ECG Pages: 188

Brand: Fagor Pages: 2

Brand: Atag Pages: 40

Brand: Daewoo Pages: 42

Brand: minibaby Pages: 9

Brand: Hotpoint Pages: 16

Brand: Smeg Pages: 38

Brand: Thermador Pages: 66

Brand: Bartscher Pages: 32

Brand: AYA Pages: 48

AdorinaDry V400

Brand: V-ZUG Pages: 100

Brand: Asko Pages: 28

Brand: Baumatic Pages: 44

Brand: Hansa Pages: 36

DW60A6092 Series

Brand: Samsung Pages: 31

DW60M9530F Series

Brand: Samsung Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands