Insignia NS-DWH2BS8 Installation Manual Download Page 10 | Manualshive

Page: 10 / 24

background image

10

NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8

www.insigniaproducts.com

Installation instructions

Step 1: Check the door balance

1

Hold the top of the dishwasher firmly.

2

Open the door slowly, then release it. If the door drops, increase the spring tension. If the door closes,
decrease the spring tension.

3

Continue moving the spring pin until the door is balanced. Adjust both springs to the same tension.

Caution

• Opening the door of your dishwasher before it is

installed will cause it to tip forward. Do not open the
door until you are ready to install your dishwasher.

• If it is necessary to open the door, hold the top of the

dishwasher securely with one hand and hold the door
with the other hand.

Increase

Decrease

NS-DWH2_BS8_SS8_NS-DWR2_BS8_WH8_SS8_17-0649_Install MAN_V3_ENG.fm Page 10 Thursday, July 27, 2017 9:21 AM

«
...
8
9
10
11
12
...
»

Summary of Contents for NS-DWH2BS8

























Reviews:

No comments

Related manuals for NS-DWH2BS8

Brand: GE Pages: 72

Brand: Haier Pages: 54

Brand: Haier Pages: 84

Brand: Haier Pages: 58

DW9-TFE1 Series

Brand: Haier Pages: 52

DW12-TFE3 series

Brand: Haier Pages: 28

Brand: Haier Pages: 18

Brand: Samsung Pages: 10

Brand: Samsung Pages: 9

Brand: Samsung Pages: 7

Brand: Samsung Pages: 12

Brand: Infiniton Pages: 127

Brand: GE Pages: 40

Brand: Admiral Pages: 6

Brand: Progress Pages: 72

Brand: Bradley Pages: 25

Brand: V-ZUG Pages: 36

Brand: Jackson MSC Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands