background image

 

© 1997  Inovonics Wireless Corporation  LIT-FA416-INSTALL   

13

 

02304e 23-Oct-02 

 

Frequency Agile

 Series Transmitters (Continued) 

FA209  

Billtrap Transmitter 

3V LITHIUM

3V LITHIUM

Tamper switch 

Reset button 

Programming header

Delay selector

 

 

Program contacts:  N/O  

 EOL, internal contacts:  No 
 

Typical battery life:  1-2 years 

  Battery type (Qty. 2):  3.0V lithium CR2450N 
 

Dimensions:  2.63" x 6.19" x 0.750"

 

FA210  

Reduced-size 

Universal Transmitter 

 

3.0V

+

Tamper switch 

Reset button 

Programming header

 

 

 

Program contacts:  N/O or N/C, as needed 

 

EOL resistor:  as needed 

 

Typical battery life:  4 years 

 

Battery type:  3.0V lithium DL123A 

 

Switch trigger:  1.5 seconds, minimum 

 

Dimensions:  3.55" x 1.70" x 0.920"

 

FA210W  

Reduced-size 

Universal Widegap Transmitter 

 

3.0V

+

FA210W Widegap
Reed switches

Reed switch
indicator

 

 

 

Program contacts:  N/O or N/C, as 

needed 
 

EOL resistor:  as needed 

 

Internal contact:  as needed 

 

Typical battery life:  4 years 

 

Battery type:  3.0V lithium DL123A 

 

Switch trigger:  1.5 seconds, 

minimum 
 

Dimensions:  3.55" x 1.70" x 0.920"

 

 

FA250  

High PowerTransmitter 

3.0V

+

Reset Button

Tamper Switch

Programming Header

External contact
Terminals

 

 

 

Program contacts:  N/O or N/C, as needed 

 

EOL resistor:  as needed 

 

Typical battery life:  1-2 years 

 

Battery type:  3.0V lithium DL123A 

 

Switch trigger:  1.5 seconds, minimum 

 

Dimensions:  1.25" x 6.00" x 0.750"

 

 

 

 

 

Note: Batteries are always supervised. Lithium batteries are capacity-tested at 18-hour intervals.  

Typical battery life is based on 60-second check-in. 

The transmitter will deactivate 2 weeks after low battery is detected.

 

 

Summary of Contents for FA416

















Reviews: