Innovatech Predator 2400 Page 10 Owner'S Manual Download | Manualshive

Page: 10 / 61

background image

Predator 2400

Owner’s Manual

OIPB-

IO-2003-P2400 GRINDER

10 |

P a g e 0 1 / 1 7 / 2 0 1 9

MAINTENANCE

Clean machine after every use. To clean machine, use a low pressure water hose or air
pressure. Do not use a high PSI pressure washer. This could force water into areas of the
machine unintentionally and damage parts. A regular inspection of machine for wear and
damage should be done on a regular basis. If any parts have been damaged or have
excessive wear, they should be replaced. If a belt needs being replaced, please see separate
instructions.

TROUBLESHOOTING

1.

Check to see if main power supply is on.

2.

Check to see if emergency stop is pushed down; if it is, pull up.

3.

Check to see if manual speed pot is turned up past 1.

4.

Check all cords ends for loose connection.

5.

Check fuse in distribution box with test meter.

6.

Check to see if all phases are with right voltage (check with volt meter).

7.

Check the converter connector cable to motor.

8.

Check for error message on display of the converter.

«
...
8
9
10
11
12
...
»

Summary of Contents for Predator 2400






























































Reviews:

No comments

Related manuals for Predator 2400

Brand: Janome Pages: 31

Brand: Republic Bank Pages: 18

RootsScrub B6050

Brand: ROOTS Pages: 22

Brand: Lumina Pages: 40

Brand: Janome Pages: 13

Brand: Janome Pages: 115

Brand: Singer Pages: 61

Brand: Olivetti Pages: 16

Brand: Singer Pages: 40

SWEEPER VAC V-036

Brand: Vax Pages: 12

aerobic twisting stepper

Brand: Brookstone Pages: 14

LBH-1790A Series

Brand: JUKI Pages: 5

Brand: JUKI Pages: 33

Brand: Bosch Pages: 32

Brand: Easy@Home Pages: 86

Brand: Windsor Pages: 33

Brand: Windsor Pages: 18

Brand: Windsor Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands