manualshive.com logo in svg

Innova AirLeaf B10642, Installation Manual, Page: 11 / 40

Share
Download
Innova AirLeaf B10642 Installation Manual Download Page 11

11

S

I

U

2.10 

H2

H4

AIR

N540022B

A

2.9 

EN

Continuous modulation circuit board for connecting remote thermostat 

(only for models ESE645 - ESE648)

LED Indications (Ref. A) (only for models ESE645 - ESE648)

The circuit board for remote control is for all functions of 
the fan coil system from the wall-mounted remote control 
EDA/EDB649 - EWG/EWW649.
A remote control can be connected to a maximum of 
30 fan coils that will be controlled in broadcast mode 
(simultaneous commands to all fan coils).
It can be installed on all versions, the board has a green 
LED that indicates the operational state and any anomalies.

The main operational parameters, the set point and the 

room temperature are transmitted from the wall-mounted 
remote control EDA/EDB649 - EWG/EWW649 to all 
terminals connected to the network, allowing unified 
operation.
Refer to the instructions for this control for use of the fan 
coils.
The 10 kΩ water temperature probe positioned in the 
device battery regulations the minimum level when heating 
(30°C) and the maximum level when cooling (20°C).

Green LED: Indicates that the unit is 

operational. Flashing indicates an anomaly.

LED off: unit is off or has no power.

Segnalazioni d'errore

Error

Display

Communication error. The circuit board expects continuous information exchange on the serial line 
with the wall-mounted control EDA/EDB649 - EWG/EWW649. If this exchange is lost for more than 
5 minutes, an error warning is displayed and the unit deactivated.

6 f pause

Problem with fan motor (e.g. blockage caused by foreign objects, faulty rotation sensor).

2 f pause

Water temperature probe fault for 2-tube versions (H2).
In this case, ensure that the probe installed is 10 kΩ.

3 f pause 

Cold water temperature probe fault for 4-tube versions (H4).(Only for ESE648) positioned on the 
main battery.

5 f pause

GRID contact open

Continuous rapid
flashing 

Water demand detected by probe H2 insufficient (above 20°C when cooling, below 30°C when 
heating). Stops the fan until the temperature returns to a suitable level to satisfy the demand*.

1 f pause

Only for board ESE648 (4-tube machines): cold water demand detected by probe H4 insufficient
(above 20°C). Stops the fan until the temperature returns to a suitable level to satisfy the demand*.

4 f pause

* If after having powered the board the water probe is 
detected, start-up takes place with the minimum and 
maximum water temperature thresholds.

The board also has a function when there is no probe, in 
such cases the fan stop thresholds are ignored.

Summary of Contents for AirLeaf B10642









































Reviews:

No comments