Innotech Vaisala WMT Installation Instructions Manual Download Page 17 | Manualshive

Page: 17 / 24

background image

Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor

Page 17

© Mass Electronics Pty Ltd 2011

Edition 6.0 dated 04/01/2017

BACnet Tab

Under the BACnet tab you can configure or modify the following settings:

•

BACnet Instance number

•

BACnet Datalink protocol

•

BACnet MS/TP Settings

Please note that the MS/TP settings can only be modified if the

BACnet Datalink

is selected as MSTP.

Otherwise these settings cannot be modified and will be unaccessible.

Figure 13:

Configure IG04 settings in FusionLIVE – BACnet tab

It is recommended to leave these settings at the default values, as illustrated in Figure 13 below.

The default BACnet Instance number for the IG04 BACnet Gateway is 1509.

«
...
15
16
17
18
19
...
»

Summary of Contents for Vaisala WMT

























Reviews:

No comments

Related manuals for Vaisala WMT

Brand: M86 Security Pages: 86

Brand: Panasonic Pages: 4

Brand: TELETECH Pages: 4

Brand: Eneo Pages: 52

Brand: Response Pages: 38

Brand: System Sensor Pages: 2

Brand: XNET Pages: 23

Brand: Axis Pages: 2

Brand: DSE Pages: 4

Brand: Fike Pages: 52

HOMEGUARD HGNVK-930CAM

Brand: Iget Pages: 6

Brand: Axis Pages: 7

Brand: XTS Pages: 32

DH-HAC-HFW1200TL

Brand: Dahua Pages: 30

Brand: Homeguard Pages: 8

Brand: Robotics Technologies Pages: 11

Brand: Air Techniques Pages: 28

Brand: Genie Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands