background image

10

AD-400 Networked Wireless Lock User Guide

COMMUNICATION PROPERTIES

Property

Description

Heartbeat

When the lock is idle, the heartbeat is a brief communication from the lock to the 
PIM400.
The heartbeat allows an idle lock to check for messages from the PIM400. By 
default, this occurs every 10 minutes, but can be adjusted in the range of 15 
seconds to many hours. Short heartbeat intervals are suggested only if “Time 
Zones” accuracy of less than 10 minutes is desired.
The value indicates the time between the heartbeats. Set the value to a shorter time 
(lower number) to achieve more frequent communication while the lock is idle. Set the 
value to a longer time (higher number) to achieve less frequent communication.
A smaller value will decrease battery life. A larger value will increase battery life.

Immediate

When the lock is used, there is immediate communication to and from the PIM400 
regardless of the heartbeat interval.

Wake-Up On 
Radio

When enabled, this feature causes the lock to respond within seconds to a 
centralized command from the access control panel. When disabled, the lock will 
respond only during its heartbeat, which could result in a delay.

Î

Î

TestÎtheÎfunctionÎofÎWake-UpÎOnÎRadio,ÎbothÎlockÎandÎunlockÎoperations,ÎafterÎallÎ
locksÎareÎinstalled.ÎToÎtest,ÎverifyÎthatÎallÎlocksÎgoÎtoÎtheÎrequestedÎstateÎwithÎnoÎ
assistanceÎorÎintervention.ÎIfÎtestÎfails,ÎtoggleÎDynamicÎChannelÎSwitchingÎ(DCS)ÎtoÎ
itsÎoppositeÎstateÎ(offÎtoÎon,ÎorÎonÎtoÎoff).ÎThen,Îre-linkÎallÎlocksÎandÎtestÎagain.

Cache Mode When enabled and communicating with the ACP, the lock keeps a local database 

of successful access grants.
In the event of communication failure between the AD-400 lock and PIM400, or 
between the PIM400 and the ACP, access is enabled for facility codes or recent valid 
users full card numbers. 
Note: When cache mode is configured for Smart cards, the default of “full card 
numbers” must be used.
The local lock database does not capture audit events.
See the SUS User Guide for more information.

COMMUNICATION FAILURE

When communication fails between the AD-400 and the PIM400, the lock will go into Communication 
Failure Mode. If the ACP or the PIM400 lose power, the AD-400 can lock, unlock, remain as-is, or 
allow valid access without communicating to the ACP or the PIM400. This mode can be configured 
using the SUS. See the SUS User Guide for more information.

Mode

Description

Fail unsecure 
unlocked 

Lock unlocks and remains unlocked until communication is restored.

Fail secure locked  Lock locks and remains locked until communication is restored.
Fail as-is 

Lock remains in current state until communication is restored.

In addition, the lock has an internal cache, that can be enabled using the SUS, to allow limited access 
while the lock is offline. If cache mode is enabled, it is not affected by the communication failure mode 
configuration. See the SUS User Guide for more information.

Summary of Contents for Schlage AD-400





























Reviews: