manualshive.com logo in svg

Ingersoll-Rand IRN100H-OF, Installation, Operation And Maintenance Manual

Share
Download
Ingersoll-Rand IRN100H-OF Installation, Operation And Maintenance Manual Download Page 7

80448608 Rev B 

 

7

EN

RECEIPT / HANDLING 

RECEIPT

When you receive the compressor please inspect it closely. Any indication of careless handling by the carrier should be noted 
on the delivery receipt especially if the compressor will not be immediately unpacked. Obtaining the deIivery persons signed 
agreement to any noted damages will facilitate any future insurance claims.

IMPORTANT

READ THIS

LOST OR DAMAGED GOODS

THOROUGHLY INSPECT THIS SHIPMENT IMMEDIATELY UPON ARRIVAL

OUR RESPONSIBILITY FOR THIS SHIPMENT CEASED WHEN THE CARRIER SIGNED

BILL OF LADING

If goods are received short or in damaged condition, it is important that you notify the carrier and insist on a notation of the 

loss or damage across the face of the freight bill. Otherwise no claim can be enforced against the transportation company.

If concealed loss or damage is discovered, notify your carrier at once and request an inspection. This is absolutely necessary. 

Unless you do this the carrier will not entertain any claim for loss or damage. The agent will make an inspection and grant a 

concealed damage notation. If you give the transportation company a clear receipt for goods that have been damaged or 

lost in transit, you do so at your own risk and expense.

WE, AT lR, ARE WILLING TO ASSIST YOU IN EVERY POSSIBLE MANNER TO COLLECT CLAIMS FOR LOSS OR DAMAGE, BUT 
THE WILLINGNESS ON OUR PART DOES NOT MAKE US RESPONSIBLE FOR COLLECTION OF CLAIMS OR REPLACEMENT OF 
MATERIAL. THE ACTUAL FILING AND PROCESSING OF THE CLAIM IS YOUR RESPONSIBILITY.

Ingersoll Rand Company Limited

UNPACKING AND HANDLING

The compressor will normally be delivered with a polyethylene or other cover. If a knife has to be used to remove this cover, 
ensure that the exterior paintwork of the compressor is not damaged.

Incorporated within the base of the compressor are slots to enable a fork lift truck to move the machine. Ensure truck forks 
are fully engaged on both sides. Alternatively a special lifting frame can be utilized to enable a crane or hoist to move the 
compressor. Use only marked lifting points.

Once the packaging and pallet are discarded and the unit is in its final position, remove the transit brackets from the resilient 
mounts and store for future use or discard.

RELEASED 06/Feb/2018 13:48:37 GMT

Summary of Contents for IRN100H-OF

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands