Ingenico FLEX IPP320 Installation & Usage Download Page 13

 

Credit Card Plus: Ingenico iPP320

 

 
 

© 2018 athenahealth, Inc. 

Rev 1.52  -  Page 13 

If the terminal stops for an extended period of time (5+ minutes) at either the

 

"Initializing Host IP

 

or “Network 

Problem” screens

 (see images below), the terminal is unable to receive an IP address from the local network.

  

 

 

Try the following solutions: 

1.

 

Check that your Ethernet cable is connected to the Magic Box and your Ethernet connection (usually a 
wall jack or hub connection

not

 

your computer’s E

thernet port).  

2.

 

If you fix a network issue, you may need to restart the device by pressing and holding the yellow and 

#”

 keys for about two seconds.  In rare cases, it may be necessary to perform a more complete reset 

by disconnecting the cable at the back of the terminal for 30 seconds, then reconnecting. 

3.

 

Ensure that your network is set up to serve DHCP

3

 to computers that are connected to the network.  You 

may need to consult your IT department to confirm this setup. 
 

If you have been able to confirm that the terminal has an IP address by inspecting your DHCP server but you 
are 

still

 stuck at either 

the “Initializing Host IP” or “Network Problem” 

screen above, it is possible the device may 

have an IP address but is unable to resolve Elavon DNS addresses.  This can happen if other networking issues 
prevent access to these resources.  Please consult th

Advanced Network Troubleshooting

 section on to 

troubleshoot issues of this nature. 
 

Q

: Why does nothing happen when I click the “Collect Payment” link?

 

This may be happening because your browser has a popup blocker installed or activated for athenaNet

’s 

pages.

 

 

Try the following solutions:  

1.

 

Ensure that you have followed the directions in on page 4 to 

Configure Your Browser

, which should 

disable popups on athenaNet pages in Chrome

.

 

2.

 

Disable any third-party pop-up blocking software you may have installed to see if this is the cause of the 
issue. 
 

Q

: Why don’t I see the green circle or “Connected” status on the ADM page?

 

If the ADM page shows that your device is not connected, this indicates that your device is having issues 
communicating with the ADM tray application, 

or

 that the ADM tray application may not be started or 

communicating with athenaNet.

  

 

Try the following solutions: 

1.

 

Navigate to Settings in the navigation bar. 

                                                      
 

3

 

DHCP is on by default in most common consumer-level routers and most corporate networks.  In some cases, your network 

administrator may require the device’s MAC address to setup DHC

P properly.  This can be found on the label on the back 

of the device.  If your setup needs a static IP assignment, 

see “

Q: How do I assign a static IP address to an Ingenico 

terminal?

”.

 

Summary of Contents for FLEX IPP320






















Reviews: