background image

MINIMUM 18" 

(45.7cm)

FROM SIDE

MINIMUM 18"

(45.7cm)

FROM SIDE

72" (1.8m) MINIMUM 

HEIGHT FROM FLOOR

5-3/4" (14.6cm)

LEVEL HERE

11/32" OUTSIDE NUT

11/32" INSIDE NUT 
(SNUG TO CERAMIC)

5

Disconnect power at the breaker. Remove two screws from one end of trim and slide trim off opposite end. Remove grill 
by grasping it in the middle, flex grill up and lift it off. Unscrew and remove both end reflectors. Unhook element clips 
at each end of the heater and remove nuts from end of element to remove the existing quartz tube. Carefully install the 
new element. Remove one nut from end of the new element. Install wire by sliding high temperature ring terminal onto 
element screw and replace nut. Use a thin 11/32" wrench to hold inside nut. Nuts must make a tight connection. Close 
element clips over tube and reinstall end reflectors, and snap protective grill back in, then reinstall trim.

NOTE:  Hold ceramic element firmly while 

tightening nut to prevent damage to 
element. Nut should be tightened snug.  
A loose connection can cause the  
element to short or fail prematurely.

REPLACEMENT ELEMENT INSTALLATION 

(VISIT INFRATECH-USA.COM FOR VIDEO INSTRUCTIONS)

SCAN FOR 

VIDEO 

INSTRUCTIONS

Heater must be installed with the quartz tube horizontally level. For maximum tube life, use a level to find the optimum 
position for the heater’s body. Always maintain the minimum clearances from the heater body to any combustible 
materials.

REPLACEMENT ELEMENTS

 

PART NUMBER 

MODEL 

LENGTH 

WATTS 

VOLTS 

FITS

 

10-7025 

E-1612-SL 

22-3/8" (0.6m) 

1600 

120 

SL-1612

  10-7030 

E-1624-SL 

22-3/8" (0.6m) 

1600 

240 

SL-1624

  10-7035 

E-2424-SL 

35-3/8" (0.9m) 

2400 

240 

SL-2424

  10-7040 

E-2428-SL 

35-3/8" (0.9m) 

2400 

208 

SL-2428

  10-7055 

E-3024-SL 

56-3/8" (1.4m) 

3000 

240 

SL-3024

  10-7060 

E-3028-SL 

56-3/8" (1.4m) 

3000 

208 

SL-3028

  10-7075 

E-4024-SL 

56-3/8" (1.4m) 

4000 

240 

SL-4024

  10-7080 

E-4028-SL 

56-3/8" (1.4m) 

4000 

208 

SL-4028

Consult label on back of heater 

for proper watts, voltage, and  

replacement element part number.

Need help? 

To order replacement 

elements for your Infratech 

heating system, please contact  

us via phone or visit our website.

Summary of Contents for SL Series









Reviews: