REPLACEMENT PARTS
PART NUMBER
PART DESCRIPTION
QUANTITY
13-7008
End Reflector (Set of 2)
1
13-7004, 13-7002, 13-7000
Body Reflector - Fits (SL16), (SL24), (SL30/40)
1
13-7034, 13-7032, 13-7030
Lead Wire Set - Fits (SL16), (SL24), (SL30/40)
1
13-7020, 13-7022, 13-7023
Mounting Brackets (Set of 2) (Stainless Steel, Black)
1
13-7014, 13-7012, 13-7010
Grill Guard (SL16), (SL24), (SL30/40)
1
13-7028, 13-7026, 13-7024
Stainless Steel Trim (SL16), (SL24), (SL30/40)
1
13-7028BL, 13-7026BL, 13-7024BL
Black Trim (SL16), (SL24), (SL30/40)
1
6
HEATER COVERAGE AREAS
MODEL
WATTS
MOUNTING HEIGHT
AVERAGE
COLD
PROTECTED
SL 1624
1,600
6' - 7' (1.8m - 2.4m)
6' x 6' (1.8m x 1.8m)
4' x 4' (1.2m x 1.2m)
8' x 8' (2.4m x 2.4m)
SL 2424
2,400
7' - 8' (2.1m - 2.7m)
7' x 7' (2.1m x 2.1m)
5' x 5' (1.5m x 1.5m)
9' x 9' (2.7m x 2.7m)
SL 3024
3,000
7' - 9' (2.1m - 2.7m)
8' x 8' (2.4m x 2.4m)
6' x 6' (1.8m x 1.8m)
10' x 10' (3.0m x 3.0m)
SL 4024
4,000
8' - 10' (2.4m - 3.4m)
10' x 10' (3.0m x 3.0m)
8' x 8' (2.4m x 2.4m)
12' x 12' (3.7m x 3.7m)
NOTE: Mounting height should not be less than 6' (1.8m) if the heater is labeled as UL Listed and 8' (2.4m) if the
heater is labeled as CUL Listed. Indoor or well-protected environments will generally exceed average. Heaters
can provide less than average coverage in extremely cold/windy conditions.
GENERAL NOTES
• INFRATECH QUARTZ TUBE ELECTRIC HEATERS are furnished with wall/ceiling mount swivel brackets. These brackets
may be discarded when the heater is hung with chains, or other special bracketing.
• See sales literature and price list for full listing of models, descriptions, amperages, and voltages. At times, especially when
the mounting height might be quite low, an increased number of smaller heaters can help prevent overheating.
• Heaters up to 15 AMPS can be controlled with a simple INF Input Regulator. This low cost controller, which is actually an
infinite switch, gently pulses the heat on and off at regular intervals when not on full power.
• For ideal comfort heat, the best solution is to heat from two sides rather than from just one side. However, there are times
when this is not practical.
• Coverage areas are approximate dimensions and will vary depending on prevailing and personal comfort levels.
• Indoor or well-protected environments will generally exceed average (see charts). Heaters can provide less than average
coverage in extremely cold/windy conditions.
MAINTENANCE INSTRUCTIONS
• Before performing any maintenance, power must be disconnected and the heater cool to touch.
• Heater housing, reflectors, and heating element can be rinsed with a hose or wiped down with isopropyl alcohol,
acetone, or glass cleaner. Use a clean, scratch-free rag or paper towel. Any oxidation, surface rust, or discoloration can
be removed with a stainless steel cleaner or metal polish on the bare metal surface.
• Make sure all water, solvents, or cleaners are removed and the heater is dry before reconnecting the power.
