background image

Introduction

 

Infoblox Installation Guide

Hardware Components

The Infoblox-2000-A is a 3-U platform that you can easily mount in a standard equipment rack using the mounting 
brackets and bolts that ship with each appliance. The front panel components include the LCD (liquid crystal 
display) panel and navigation buttons, communication ports, hard disk drives, and indicator lights. The back panel 
components include power connectors and switches, fans, air vents, and a backup battery unit.

Front Panel

The front panel components are shown in 

Figure 2

 and described in 

Table 1

. For explanations of the Ethernet port 

LEDs, and console and Ethernet port connector pin assignments, see 

Ethernet Port LEDs

 on page 6 and 

Connector 

Pin Assignments

 on page 6.

Figure 2  

Infoblox-2000-A, Front View

Table 1  

Front Panel Components

Component

Description

LCD Panel

An LCD screen that displays HA (high availability) status, network settings, software version 
number, hardware serial number, and software licenses. Additionally, you can view and 
configure the IP address, netmask, and gateway for the LAN1 port.

USB Ports

MGMT Port

Console Port

Power Indicators

HA Port

LAN2 

Port

Drive Indicators

LCD Panel

Navigation 

Buttons

LAN1 

Port

Drive 1

Drive 2

Drive 3

Drive 4

Summary of Contents for Infoblox-1050-A





























Reviews: