background image

RM24100D operating manual                                                                                             Page 6

4 Specifications

Frequency range

2.4GHz ISM band (2407.5-2467.5MHz)

Protocol

IEEE 802.15.4 compliant

Modulation

OQPSK (Offset Quadrature Phase Shift Keying)

Spread Spectrum Technology

DSSS (Direct Sequence Spread Spectrum)

Number of channels

12 direct sequence channels

Transmit Power

63mW (18dBm) conducted, 100mW (20dBm) EIRP with a 2.1dBi dipole 
antenna (Output transmit power is configurable via software)*,**,***

Receiver sensitivity

(1% Packet Error Rate) -100dBm

Range (2.1dBi dipole antenna)

Indoor/urban (+-90m/300ft), outdoor/line-of-sight (+-1km/0.6 miles)

RF data rate

250 kbps

Antenna connection

RPSMA (reverse polarity SMA)

Antenna impedance

50 ohms unbalanced

Antenna

2.4GHz 2.1dBi omni-direction dipole antenna

Enclosure Material

Polymide (PA 6.6)

Enclosure Color

Green

Enclosure Dimensions

79mmx90.5mmx25mm (din rail mount)

Data Connection

Side terminals or DB9 female

Operating Temperature Range

-40

°

C to 85

°

C (14

°

F to 122

°

F) industrial temperature range

Humidity

<85% non-condensing

Supply Voltage

8 to 30VDC switch mode power supply with built in 33V over voltage and 
reverse voltage protection

Current Consumption

Approximately 200mA (@18dBm transmit power
Average current while streaming data at 9600 baud approx.  50mA @12V

Baud Rate

1200 to 115200 bps(non-standard baud rates also supported)

Agency approved radio 
module 

US FCC Part 15.247, Industry Canada (IC), Europe (CE)* **

RS485/RS422 Termination 
resistor (RS485/RS422 
models only)

Jumper selectable 120 Ohms (Jumper J1 internal on PCB)

*When operating in Europe the maximum transmit power output level must not exceed 10dBm. Additionally, European 
regulations stipulate an EIRP power maximum of 12.86dBm (19mW).
**Maximum transmit power output levels and local radio frequency regulator bodies must be obeyed in the country of 
operation.
***Maximum transmit power output levels and local radio frequency regulator bodies must be obeyed in the country of 
operation.

5 Antenna Range

Various antennas can be used to increase/enhance the range of the radio modems. Below is an indicative drawing of 
various antennas and there ranges/directions of propagation.

Summary of Contents for RM24100D










Reviews: