User Manual
2 of 18
Rev.1.00
2020-05-25
TLD5542-1IVREG-EVAL evaluation board
Table of contents
1
About this document ......................................................................................................................... 1
Table of contents ...................................................................................................................... 2
2
Description .............................................................................................................................. 3
3
Quick start procedure ............................................................................................................... 4
3.1
Setup as LED driver limp home mode (microcontroller-less) ............................................................... 4
3.2
Set up as voltage regulator - Limp home mode (μC-less – no PC GUI) .................................................. 5
3.3
Connecting the board to the μIO stick.................................................................................................... 6
4
Infineon μIO stick and Infineon Toolbox ..................................................................................... 8
4.1
Install and launch Config Wizard ............................................................................................................ 9
5
Board control with PC GUI ........................................................................................................10
5.1
Basic user interface ............................................................................................................................... 10
5.2
Engineering user interface .................................................................................................................... 11
6
Operating range and power derating ........................................................................................13
7
Electrical characteristics ..........................................................................................................14
8
PCB layout ..............................................................................................................................15
9
Schematic ...............................................................................................................................16
Revision history ...............................................................................................................................17
