Infineon TLD5542-1IVREG-EVAL User Manual Download Page 18

 

 

 

 
 

 

 
Published by 
Infineon Technologies AG 
81726 München, Germany 
 
© 2020 Infineon Technologies AG. 
All Rights Reserved. 

 
Do you have a question about this 
document? 
Email: 

[email protected] 

 
Document reference  

IMPORTANT NOTICE 

The information given in this document shall in no 

event  be  regarded  as  a  guarantee  of  conditions  or 

characteristics  (“Beschaffenheitsgarantie”) .  

 

With  respect  to  any  examples,  hints  or  any  typical 

values  stated  herein  and/or  any  information 

regarding  the  application  of  the  product,  Infineon 

Technologies  hereby  disclaims  any  and  all 

warranties  and  liabilities  of  any  kind,  including 

without limitation warranties of non-infringement of 

intellectual property rights of any third party.  

 

In addition, any information given in this document 

is  subject  to  customer’s  compliance  with  its 

obligations  stated  in  this  document  and  any 

applicable legal requirements, norms and standards 

concerning customer’s products and any use of the 

product  of  Infineon  Technologies  in  customer’s 

applications.  

 

The data contained in this document is exclusively 

intended  for  technically  trained  staff.  It  is  the 

responsibility of customer’s technical departments 

to  evaluate  the  suitability  of  the  product  for  the 

intended  application  and  the  completeness  of  the 

product  information  given  in  this  document  with 

respect to such application.     

 

 

For further information on the product, technology, 

delivery  terms  and  conditions  and  prices  please 

contact  your  nearest  Infineon  Technologies  office 

(

www.infineon.com

). 

 
WARNINGS 

Due to technical requirements products may contain 

dangerous substances. For information on the types 

in  question  please  contact  your  nearest  Infineon 

Technologies office. 

 

Except as otherwise explicitly approved by Infineon 

Technologies  in  a  written  document  signed  by 

authorized 

representatives 

of 

Infineon 

Technologies, Infineon Technologies’ products may 

not be used in any applications where a failure of the 

product or any consequences of the use thereof can 

reasonably be expected to result in personal injury. 

 

 

 

 

Edition 2020-05-25 
 
 
 
 
 
 
 
 
 
 
 
 

UM TLD5542-1IVREG_eval 

 

 

Trademarks  

All referenced product or service names and trademarks are the property of their respective owners. 

 

 

  

 

Summary of Contents for TLD5542-1IVREG-EVAL



















Reviews: