Infineon Technologies TC1796 User Manual Download Page 1803 | Manualshive

Page: 1803 / 2150

background image

TC1796

Peripheral Units (Vol. 2 of 2)

General Purpose Timer Array (GPTA)

User’s Manual

24-148

V2.0, 2007-07

GPTA, V2.0

24.2.7

Programming of a GPTA Module

A hierarchical top-down design approach may be used to implement a complex signal
processing unit as follows:
•

Partitioning the complex signal processing unit into simple function units.

•

Implementing each simple function unit by configuring the LTC and/or GTC cells
which can be tied together for realizing a common signal operation.

•

Implementing necessary signal pre-processing tasks by configuring the FPC, PDL,
DCM and PLL cells accordingly.

•

Defining and configuring all input/output port pins required as clock source, trigger
input or signal output.

Table 24-15

summarizes all of the software tasks to be implemented for getting a GPTA

unit into operation.

Table 24-15 Software Tasks Controlling a GPTA Unit

GPTA Shell Initialization
GPTA Module Clock Enable
Fractional Divider Setting
Module Enable
Configuration of Interrupt Handling
GPTA Kernel Initialization

FPC:

PDL:

Selection of Operating Mode (Prescaler,
Filter or Feed-Through)

Selection of Operating Mode (Phase
Discriminator or Feed-Through)

Input Channel Selection

2- or 3-Sensor Mode Selection

Clock Selection

PLL:

Configuration of Prescaler Factor or
Debounce Mode

Selection of Input Channel

DCM:

Estimation of Input Signal Period Width

Selection of Reset Event for Timer

Configuration of Output Signal Frequency

Selection of Trigger Source for Capture
Event

Handling of Input Signal Period Length
Variation

Selection of Trigger Source for Capcom
Register Update

Interrupt Request Enable on End of Output
Pulse Generation

Interrupt Request Enable on Input Edge or
Compare Event

«
...
1801
1802
1803
1804
1805
...
»

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: Panasonic Pages: 16

Brand: Abus Pages: 12

Brand: Samson Pages: 52

Brand: ZIGBEE Pages: 5

Brand: Mackie Pages: 4

Brand: Maclaren Pages: 15

Brand: Maclaren Pages: 9

Brand: Maclaren Pages: 40

Brand: National Instruments Pages: 8

Brand: Vaillant Pages: 32

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 40

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Forcepoint Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands